GS6SHAXMB00 Whirlpool Refrigerator - Instructions

If you follow the video to the letter it's a piece of cake

Unscrewed water inlet support bracket,placed new inlet valve next to old valve with same orientation.one by one disconnected water lines and power leads and reconnected to same position on new valve.Reattached bracket and job done..Access to valve very easy.

Replaced the emitter and receiver boards by following the video instruction. Unscrew the cover plate, disconnect the wire, remove and replace the board and re-install. Repair was very easy and the unit is back in service.

1. Remove 3 phillips head screws with #2 phillips screwdriver. 2. Gently pull mounting bracket outward from freezer case. 3. Using fine needle nose pliers remove clip washer from lower end of flipper mounting rod. 4. Note position of flipper spring and pull mounting rod upward far enough to insert downward through new flipper and spring. 5. Install clip washer removed in step 2. Position assembly onto freezer cabinet and secure with screws removed in step 1.

remove old ice maker no fasteners and one electrical plugin and transfer plate from old ice maker and reinstall very simple. was delighted to see it arrive so soon........thanks for that

Used the instructions provided on the web site. They were very clear and easy to follow. I might add, I am an 82 year old 30 year military retiree and I am used to problem solving. Yours in service, Jimbo

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

took screwdriver, took out old parts. replaced with new parts. plugged fridge back in, turned on receiver. We have ice! Real Easy to install! Thank you Part Select.

The hardest part was figuring out how to get the front panel escutcheon panel off. With the putty knife under the bottom flange, you need to push down with some effort on the part of the flange where the drip pan slides in and twist the putty knife to disengage the locking tab. Once the panel is off, the rest of the job is easy with the aid of your video. Everything works like new...thanks.

Removed old valve. New valve does not provide for filter without modification. oOld valve used compression nut which had to be removed. Smooth cut with utility knife and push in. Needed a 1/4 inch compression coupling to hok up ice maker connection to 1/4 inch plastic hose fro the valve.

I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

A repairman wanted $600.00 to fix our ice maker. I paid him $88.00 for his "service call" & asked him to leave. I ordered & replaced the ice maker machine & the ice maker still would not work, so I replaced the 2 optics boards next. Replacing the ice maker was most challenging because the plug is so hard to get at, but the 2 optics boards were pretty easy. Just watch the video on PartSelect.com. Work slowly & take your time when pulling out & replacing the optics boards. There were a total of 6 screws for the 2 optics boards. It took me approximately 10 minutes to replace both boards, & now my ice maker is working perfectly! I am thrilled!!

Removed and replaced the condenser motor fan kit. This was a very easy tear down and replacement of a bad component. Removed 4 screws to remove the bracket holding the fan motor kit pulled it out and replaced with the new unit (4 screws supplied) plgged in adapter cord (supplied) and re-installed took about 10 minutes.

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

Watched the video it was right on, no problem.