Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GS2624PEKW

GS2624PEKW Maytag Refrigerator - Overview

Get Parts and Repair Help for GS2624PEKW

If you know the refrigerator repair part you need, you can browse the list of all parts on the GS2624PEKW, or you can search by name or part description. You can also find your part by where it is located on the GS2624PEKW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for GS2624PEKW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$22.07

Light Switch

This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is t...

$5.25

Crisper Frame Support

Note: If the wall anchor that this piece mounts on is broken, then the support is needed. (Order per Model#)

$30.12

Fan Blade

Used with Evaporator Fan Motors.

$5.76

Door Closure Cam Kit

This door closing cam kit is intended for use on the bottom of your refrigerator and freezer door hinges. The cam helps close the doors and to lifts them slightly when opened. If your door will not open or close, or will not stay closed, there could be an issue with the door close cam. Other common symptoms associated with the door close cam are: the door is sweating, the fridge is too warm, or a clicking sound can be heard coming from the door. If your refrigerator has an ice and water dispenser, you will need to disconnect the power and water to the unit before you begin the repair.

$21.84

Light Switch

$32.03

Thermistor

Long harness thermistor kit.

$16.54

Butterfly Handle Mount

This mount is used to connect the handle and trim together. Sold individually.

$6.54

Toe Grille Clip

Sold individually.

$6.49

Freezer Shelf Support

$264.95

Electronic Control Board

This board will need to be programmed upon installation.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Freezer is cold, Refridgerator is not as cold as it should be

  • Customer: Russell from Hardinsburg, KY
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 290 of 350 people found this instruction helpful
Having seen this problem before in other equipment so I had an idea where to look. Problem: the automatic defrost function was not operating. Looking through openings in the back panel of the freezer compartment, you could see the evaporator coils and fins were a solid chuck of ice. There are three logical components to check. Heater element, thermostat ... read more

defroster mode was not working causing freezer to ice up and refrigerator to be warm. Also fan was running continuely

  • Customer: James from Welches, OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 148 of 168 people found this instruction helpful
The hard part for me was figuring out which part was causing the problem. I read what others had done and followed their test methods. I checked the defroster heater for continuity and the defroster thermostat to make sure it was closing. the defroster termostat has to be cold to check it. You will need to check it while it is in ice or take it out and put i... read more

Top unit was not getting cold

  • Customer: Gregory from Lexington, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 129 of 145 people found this instruction helpful
First thing to do is take two screws off where the door closes.I removed the light sheild off by pushing it to back of refrig.The most hardest part is removing the complete panel,I took a small flat blade scraper to ply down to get small access than you need to put alot of pressure to start getting the panel to start coming off there are alot of pegs to free... read more