Models > GS24Y8DV

GS24Y8DV Maytag Refrigerator - Overview

Get Parts and Repair Help for GS24Y8DV

If you know the refrigerator repair part you need, you can browse the list of all parts on the GS24Y8DV, or you can search by name or part description. You can also find your part by where it is located on the GS24Y8DV by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for GS24Y8DV parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.82

Light Bulb - 40W

Sold individually.

$126.87

Ice Maker

This replacement ice maker mechanism does NOT come with a cover, a wire harness, or the mounting hardware. Must be ordered separately.

$2.70

Screw

This screw is sold individually.

$37.21

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$7.28

Light Rocker Switch

$31.14

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

$2.70

Hose Clamp

$3.32

Light Bulb - 7W

Sold individually. This bulb is a 7 watt appliance incandescent light bulb.

$18.32

Water Fill Cup and Bearing

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 185 of 255 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 77 of 80 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

not making ice

  • Customer: Pat from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 45 of 51 people found this instruction helpful
Installed new ice maker. It was easy - loosen two screws and unplug old wire harness. Put new unit in place. Did not realize new unit would not come with wire harness, but transferred old one to new ice maker (easy) and, "voila" some ice in 24 hours -- much ice since then. I am a 68 year old woman and it was "sort of fun" doing this job. read more