Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GS22X8W

GS22X8W (DR16A) Maytag Refrigerator - Overview

Get Parts and Repair Help for GS22X8W

If you know the refrigerator repair part you need, you can browse the list of all parts on the GS22X8W, or you can search by name or part description. You can also find your part by where it is located on the GS22X8W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for GS22X8W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$40.25

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forced-air cooling for the condenser coil.

$21.05

Icemaker Fill Tube

This fill tube grommet is used to supply water to the icemaker and is partially located in the refrigerator/freezer wall.

$18.42

Leveling Leg

Sold individually.

Sensor Shut-Off Arm

This part signals the icemaker to stop making ice once the bin has reached a desired amount.

$2.80

Screw

Sold Individually.

Crisper Drawer Glass Shelf

Single Lamp Socket Kit

NOTE: This is now the single lamp kit socket. The dual lamp kit socket is no longer available.

Crisper Drawer

This clear crisper drawer is twenty inches long. It is made entirely of plastic.

Secondary Seal Clip

This seal clip is to help fasten the gasket to the door of certain refrigerators and it's sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 175 of 195 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 124 of 132 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 90 of 108 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more