Models > GLTF2940FS1 > Instructions

GLTF2940FS1 Frigidaire Washer - Instructions

All installation instructions for GLTF2940FS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLTF2940FS1
76-90 of 243
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

excessive vibration

  • Customer: Jon from Holland, MI
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 2 of 3 people found this instruction helpful
I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

Vane broke off inside drum

  • Customer: Glen from Redondo Beach, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
Inserted new vane into slots in the drum. I then held the front of the drum while I slid the vane tabs in place by pushing the vane to the back of the drum. Once the vane was in place, I screwed in the screw that came inside the vane kit.

It would not start

  • Customer: Garry from Burlington, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
I unplugged it from the outlet, undid the two screws from the top, then slid it off, opened the door and undid the two screws from the door switch lifted it out relaced it with the new one, screwed it back into place, replaced the top, plugged it back in and away it went.
Garry

the latch broke

  • Customer: Sarah from Gilford, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
It was very easy. I simply unscrewed the 2 screws set the new latch into place and replaced the screws.

Washing Machine would drain but not spin.

  • Customer: Kelly from Henderson, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.

Wouldn't start

  • Customer: Anne from Storrs, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
With the help of PartSelect's diagnosting tool it was easy to find the right part. The part arrived very fast and the installation was "child's play" by following PartSelect's video. I must have saved > $100. Thank You very much. -Anna-

Broken shock

  • Customer: Ron from Blaine, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

broken shock

  • Customer: John from Glennallen, AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
removed front panel and used deep socket to remove pins that hold shocks. front left shock took most of the time because of hoses and a unit in the back that needed to be released to be able to remove the pin on the bottom. the right shock was a piece of cake to replace. used a hammer to pull the pins into place (i did not use it to tap on them ) . lots of bloddy fingers from sharp edges.

Washer was "clunking" when in use

  • Customer: Mike from Central Square, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I replaced both shocks, as both shocks were broken! Keep in mind that Parts select packages them in pairs. I order 2 packages or 4 shocks, guess I have another pair for ~ 5 years from now. These are located under the front bottom panel, so no need to isolate water lines or even pull this sucker away from the wall. Tight clearances are the only factor from making this really easy. Use some Vaseline to assist inserting the new plastic pins.

Noisey shock absorber

  • Customer: Ed from Clackamas, OR
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
The parts came with instructions They stated to remove the front panel. This only gets to one side for a difficult repair. I removed the back panel then it was a snap. Easiest with two people.

shocks broke away from washer drum

  • Customer: Rita from Cambridge, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
replaced the two shocks with the new ones by removing the pins that held the old ones in place.

dryer would not spin

  • Customer: Robb from North Huntingdon, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
Removed old shock abs. (both sides). The one side, I had to remove the speed control board to access the lower nut on the one shock. Install was fairly easy however, it did not fix the washer. Apparently there was something else (either a switch, the control board or the motor) needs replaced too.

washer drained withn no spin

  • Customer: William from Lancaster, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Remove top of washer, remove door lock assembly,install new assembly replace top.

One shock was broken

  • Customer: Larry from Alamo, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the front access cover and the rear cover. It was also necessary to remove the water level sensor (attached to the tub drain hose) to access one of the shocks. Not having a 1/2" deep socket, I used a 2" piece of 1/2" copper pipe to depress the locking tab on the shock attachment pins--worked great. Pulled the pins out with pliers. Putting the pins back in after replacing the shocks was easiest to do using 'channel-lock' pliers to grab the bracket and the pin head and squeeze in the pin. The only problem was that my copper pipe piece fell into the drain hose when removing one of the pins! Had to take the drain hose loose to fish it out.

i broke the soap dispenser on my washer

  • Customer: GLENN from MADISON, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 10 people found this instruction helpful
love parts select have used them several times for parts great company
All Instructions for the GLTF2940FS1
76-90 of 243