GLTF1670AS0 Frigidaire Washer - Instructions

1. Turned off water to washing machine.
2. Used plyers to disconnect the hoses at the back of the washer.
3. Unscrewed old inlet valve from back.
4. Opened top panel of washer and disconnected hose running to wash basin.
4. Lifted the old unit out and unplugged electrical wiring.
5. Reverse above and you're finished!
If you're reading this you can probably do the repair.
Saved myself $500+ on a new washing machine. Wife is happy.

Drain hose should come with the two clips (45B)that hold the drain hose to the back of the machine. I had to cut the old hose off. Then very carefully remove the clips from the inside of the machine with a pair of pliers.

I unplugged washer from wall, removed lower front panel, two screws, then unplugged the pump motor, then removed the two hoses going to and from the pump, spring clamps on hoses, used pliers, removed the two screws with a nut driver that hold the pump/motor assembly to the frame. I then reversed the whole procedure and all is fine now.
I also noticed that the new pump impeller has four blades and the old one had only three, both old and new are made in italy, I assume this makes the pump more efficient.
End of story!!!!!!!!

i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther

I replaced both shock absorbers that hold the drum on a front loading washer. They both snapped at the base and have since been replaced by a different style shock absorber. There are 2 pins that hold each part in place. I took 5 minutes to replace 3 pins and about an hour to replace the last one, which was in a very tight spot. After much sweating and swearing, I managed to get the pin back in. Was it worth it? ABSOLUTELY! Partsselect.com is a dream for straightforward repairs. This is the second repair I have done on this machine (which is less than 5 years old) and both repairs have cost less than $30.

The front lower access panel pops off with two Philips head screws. From there, the white pins holding the hold broken shock absorbers can be removed by pressing their locking tab down and pushing them free of the bushing.

After pulling the old, broken items out, the new ones are reinstalled the same way: place the metal end towards the drum, push the white pin through the bushing (only one way is correct) and you're almost done. Reinstall the front panel and get back to having a quiet washing machine!

The instructions that came with the new shock absorbers were very detailed and walked me through the repair step by step. The new shock absorbers are much better quality than the old tube style shocks.

easy repair. I went to the back of the washer and removed the two(?) screws that held the top panel on. Then moved to the front of the washer and unscrewed the two screws in the door frame holding the lock assembly. Pulled it up and out from the top of the washer and disconnected the three wire connections. Then I just reversed the process with the new part. It all worked great. This website rocks...
Phil
Jax, FL

Part came in, fast delivery. Took 10 minutes to install. Real easy works great.
Thanks PartSelect.

just unscrewed the old one and put a new one on.
I bought two just in case this one breaks too.

Removed front access panel, observed broken tub shock. Ordered replacement parts, included in the promptly delivered package are simple instructions. Excellent results, improved shock design, washer runs quieter.

Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!

One knob just screwed right on. The others just snaped in place. That easy!

.

I followed the great instructions provided on the site and had the old broken struts out in no time. The new ones went in without a hitch and the time it took me to unscrew and rescrew in the back of the machine was longer than the time it took me to replace the broken parts.