Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GLT3657RB05

GLT3657RB05 Whirlpool Cooktop - Overview

Get Parts and Repair Help for GLT3657RB05

If you know the cooktop repair part you need, you can browse the list of all parts on the GLT3657RB05, or you can search by name or part description. You can also find your part by where it is located on the GLT3657RB05 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.12

Torx Screw

7-18 x 3/4" - sold individually.

$4.52

Knob Skirt - Black

The knob skirt or grommet on your range goes around the knob, forming a buffer between it and the range surface. If your knob skirt is damaged, you should consider replacing it. This product is approximately 2 inches in diameter. This part is made of black plastic, and is sold individually. Many of our customers have described this repair as very easy. To complete the repair, simply remove the burner knob and the old knob skirt, replace it with the new knob skirt and re-attach the burner knob. The product contains four locking tabs that should snap into place easily.

$3.02

Screw, Igniter

This screw is sold individually.

$4.79

Screw

Sold individually.

$4.63

Knob Skirt

This white knob skirt is located between the glass top and the control knobs of your stove top. The skirt has an outside diameter of approximately 2 inches. The most common reasons...

$14.31

Surface Ignitor

Also known as Spark Electrode. This part helps your burner ignite and produce flame.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$27.54

Burner Head - 12K

This part distributes flame evenly to your cookware.

$2.90

Screw

This screw is sold individually.

$22.61

Burner Head - 6K

This is the Right Rear Burner Head.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Igniter problem on one gas burner

  • Customer: Roland from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 15 people found this instruction helpful
I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to install the replacement,... read more

I had a faulty wiring on the igniter switches.

  • Customer: Raymundo from Cerritos, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 12 people found this instruction helpful
replaced the set of igniter switches I order from Partselect .com. read more

Replace Gas Cooktop bad surface Igniter

  • Customer: Charles from Williamsburg, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
1. Turn off Gas at valve under cooktop. Unplug electric to igniters. 2. Remove all control knobs. 3. Remove grates and burner covers. 4. Remove screws from each burner head (10 screws) 5. lift and remove cooktop cover. 6. Reach under cabinet and push up main cooktop body (about 4 or 5 inches) and BLOCK. 7. AT FRONT OF COOKTOP REMOVE 2 philips screws holdi... read more