Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GLMB209DSC

GLMB209DSC Frigidaire Microwave - Overview

Get Parts and Repair Help for GLMB209DSC

If you know the microwave repair part you need, you can browse the list of all parts on the GLMB209DSC, or you can search by name or part description. You can also find your part by where it is located on the GLMB209DSC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$33.63

Relay Switch

The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the doo...

$31.36

COVER

$118.61

Cooking Tray

$30.89

Door Latch Spring

The microwave door latch spring creates tension, and engages the door latch when the door is closed. This spring is made completely of metal, and is approximately 1 inch long. If your microwave door will not open or close properly, the microwave will not start. You may need to remove the control panel to gain better access to where the spring attaches, so make sure the power is disconnected from the microwave. This part is sold individually. NOTE: Remember to discharge the capacitor for your microwave before beginning this repair. The capacitor can hold a potentially lethal charge even when the power has been disconnected from the microwave itself.

$30.38

LATCH

$74.28

Turntable Roller Guide

The roller guide sits underneath the glass turntable tray in your microwave. If your microwave turntable tray is not rotating properly, you may need to replace the turntable roller guide. The function of this part is to house the glass plate, and rotate to cook food evenly. This part has a round piece in the middle, approximately 2 inches in diameter, and 3 arms which are approximately 4 inches in length each. Each arm has a small plastic wheel on the end that supports the glass turntable tray. This part is an OEM part sourced directly from the manufacturer, and is sold individually.

$31.76

LEVER

$35.47

Motor,turntable

$272.63

CONTROL BOARD

$61.07

FUSE

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Timer would run but the microwave won't start

  • Customer: Tim from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 74 of 113 people found this instruction helpful
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up. read more

microwave wouldn't turn on but timer worked.

  • Customer: Steve from Moorhead, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 31 of 46 people found this instruction helpful
was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a 12 volt battery and... read more

Microwave would count down but not run

  • Customer: Betty from Kimball, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 27 of 41 people found this instruction helpful
After unplugging the unit remove the control face buy removing the screws. All three door switchs are on a bracket on the left. Remove the two screws holding the bracket in place and pull out. Disconnect the wires from the three switches and test each switch indivually to determine the bad one. I used a multimeter set on ohms.Replace the bad switch with the ... read more