Models > GLER341AS2 > Instructions

GLER341AS2 Frigidaire Dryer - Instructions

All installation instructions for GLER341AS2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLER341AS2
376-390 of 419
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken plastic door handle

  • Customer: Clifford from Petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped on the new one.

Turn type start switch, knob set screw came loose, further use destroyed switch stalk and twisted it out of fixture.

  • Customer: Roger from Laramie WY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Check that power cord is still disconnected from initial inspection. Remove chassis cover plate. Count and set the screws aside. Check type and fit of replacement. Twist-lock new switch into place. Swap wires onto proper terminals of new switch. Replace cover plate. Replace and tighten switch knob. Re-connect power plug. Activate new switch. Three tests successful. Return dryer to ready position. Test again- OK. Repair complete.

Loud squeaky noise

  • Customer: Alexander from GREECE NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My dryer was making a horrible squeaking noise comparable to nails on a chalkboard! I looked to get a similar used replacement because I was in a bit of a pinch for $$$, after being frustrated and not finding anything I came here and found all the parts I needed for my repair for UNDER $40!!!! I followed the super easy how to video that was provided on this website. This is the second repair I have made to this dryer, I did the heating element about a year ago. I also used this site to purchase the part and used the how to video associated with that repair. I was very surprised that I received the part the next day when I paid for regular standard shipping! Overall this was a an awesome experience and I have saved so much money repairing my dryer on my own vice paying someone to do it!!!

Knob had broken

  • Customer: Karen from Blue Eye MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Had already pulled off the broken knob--actually it had fallen off in my hand. Opened the package, pulled out the knob and pushed it onto the knob shaft. Simple. Less than one minute.

Heating element had burned out

  • Customer: Edward from Fort Wayne IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I am anything but an experienced handyman. I would always call the local appliance company to repair anything broken. This time money was a bit tight so I went on line to search directions to install a new heating element for our dryer. The PartSelect site was easy to navigate and with only the model number found the part I needed. Best of all the online instructional video so so detailed it made me believe I could do the repair. It took me less than 30 minutes to remove the burned out heating element. The new part arrived the next business day and was installed in another 30 minutes. It was so easy I feel guilty about all the other times I called service companies. Also, very upset about all the dollars I wasted. If and when any other appliance breaks, PartSelect will be the first place I will turn to. Thank you for giving me a new sense of pride in myself and saving at least $250.00. EDWARD

dryer was making a shrill noise

  • Customer: Mike from Goldonna LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the front then removed the belt that turns the drum pulled the drum strait up from the top then removed the bushing from the back wall put the new one in I also put A little grease in the new bushing to keep it from wearing installed the drum and front. realy easy. I'm A Instructor at A technical collage in Winnfield Louisiana and I used this as A project for my students.

no problem

  • Customer: Heinz from Longboat Key AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
By myself-less than 2min

Broken selector knob

  • Customer: Anthony from Crosslake MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply pressed it on. Nothing to it.

drum belt

  • Customer: MANUEL from SAN JACINTO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
so easy my daughter installed it the video was very helpful

drum making noise

  • Customer: Fred from Cle elum WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
remove top lid (snaps and remove ground wire), remove front, 2 Phillips screw; remove nylon stop (Phillips screw) remove belt from motor (access plate 2 Phillips screws). Lift back of drum from pivot, remove from cabinet. check heating element for distorted or damage coils. Straighten or replace. clean felt surface and install new felt with glue. install new sliders in drum. assemble, rotate, listen for scraping. there should be no scraping sound when rotated. scraping can be from the heating element being distorted from lack of air flow because the drum stalled. If not fixed the heating element will be damaged when powered

Loud screeching noise, barrel turned OK and Heater worked

  • Customer: Ellen from Willits CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I took the lower back panel off. Loosened the center bolt and took off the old Idler pulley. It looked brown in the middle and didn't roll well. But I wasn't sure if that was it, because the noise was so loud and sounded metal on metal. So I checked everything and vacuumed everything. After I got the new part it took me about 5 minutes to put the new one on. And dryer works fine. Thanks for the quick response and I saved about $200.00!

Dryer had no power. After doing quick troubleshoot determined Thermal Limiter was the problem

  • Customer: Darrell from McCalla AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed top from dryer. Saw I could get to Limiter without removing dryer drum.Removed Limiter with phillips head screwdriver and wires with needle nose pliers. Replaced wires and secured Limiter to dryer works like a new one.

replaced rear drum bearing

  • Customer: chuck from carroll NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

My dryers was making a loud thumping sound. Like it was off balance.

  • Customer: Dennis from Maple Shade NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Took the front off and saw the cushion was gone around the drum and glids were worn down. I ordered both parts . It took 5 minutes to glue the cushion back on around the drum and 2 minutes to snap the drum glids on.But what I couldnt believe was the amount of lint that was all over the inside of the dryer.I would suggest to anyone to take the dryer front off once a year and clean it all out . I now understand fully why there are dryer fires.But the fix was cake and it runs like new.

cracked timer knob

  • Customer: Donald from North Augusta SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pull it out and replace the new timer knob in 3 seconds.,
All Instructions for the GLER341AS2
376-390 of 419