Models > GLER331AS2 > Instructions

GLER331AS2 Frigidaire Dryer - Instructions

All installation instructions for GLER331AS2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLER331AS2
76-90 of 392
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The dryer would not dry clothes

  • Customer: Dawn from Euclid OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Girls you can do it on your own!

The easiest way is taking the back off the dryer but if you can't do that just pop the top up and unscrew the front. Just make sure you remember how you take everything out and put it back in the same.

The most difficult part is trying to line up the holes for the heating element, and holding it there while screwing the element in place.

It's a breeze!

Difficulty starting up

  • Customer: Samuel M from Jamaica Plain MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 3 of 5 people found this instruction helpful
Motor replacement requires removing/releasing the top and front of the dryer, then removing the drum through the front of the dryer. The top is hinged at the rear and the front can be pried up. The front is held by two sheet metal screws that are accessible once the top is lifted up. Three screws hold the drum to the bearing at the rear of the drum. A small access door on the rear panel allows removal of the idler arm and its spring. You will need a socket drive with a short extension to remove the fan assembly from the motor at the front of the dryer, and it has a LEFT-HAND thread. The most difficult part of the replacement, once you figure out how to access everything, is getting the drum re-attached to the bearing at the rear of the drum. It can be hard to align the three screws, and once you have that done they need to be carefully tightened a few times after rotating the drum a few cycles, to get all the play out. Once the motor was replaced the dryer works like new.

Door handle broke and came off.

  • Customer: Elizabeth from Mentor OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Simply popped it back into place, careful not to break the new handle.

dryer wouldn't heat

  • Customer: billy from millsboro DE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's seat; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in

Black lines and small tears

  • Customer: Robin from Sewaren NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Previous comments on line were so helpful.

My husband and son took the dryer apart by removing the top in order to get to the drum. Part of silver rim that the Drum Glide is attached to was broken,it had been cut somehow. They had to soder it back in place so they could attach the Drum Glide and so far it's working.

Felt- I just ordered one with the adhesive and removed the damaged section used a wire brush, applied the adhesive ( which was more than enough) waited a few minutes for the adhesive to set, applied the felt, attached binder clips to hold it in place while working on the Drum Glide. Really easy.

replaced knob, perfect fit and match

  • Customer: Paul from Beverly Hills FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
just pushed new knob on.

old knob was strip

  • Customer: DENISE K from cleveland OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
remove old knob and washer that was on it put new knob on and turn the knob dryer was save

Dryer had Loud squeek, barely spun!

  • Customer: John from Edgewater MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
First, I shut off the gas & unplugged the dryer. Then I disconnected the vent pipe so I could pull it away from the wall to access the back. Disassembling the dryer was simple.
there are 8 screws: 2 for rear access panel, 2 for top, & 4 for front panel! Once front panel is off, lift back of drum up 2 inches, then forward to get rear bearing out of it's bracket. My rear bearing had worn down so much it was 1/2 the size of the new one! It wore through the bracket down to the metal! I replaced the rear bearing & bracket assembly, as well as the belt & the spring for the belt tensioner! make sure you generously lubricate the new bearing as well as the tensioner pulley! The most time consuming part of this job was cleaning all the lint out the dryer cabinet& cleaning the drum. It works great now! I hope to get a few more years out of it!

dryer made loud scrape noise and quit drying

  • Customer: Curtis from Littleton CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I took the repair video in with me and set my lap-top on top of the washer.
My dryer did not match the type on the video exactly (mine has the controls in the front instead of on top and in the back) - however - the parts replacement for the rear drum bearing itself was the same.
After getting the front apart and releasing the drum the rest was pretty easy. Didn't really need instructions for the heating element - that was an obvious change out.
The tips on the video changing the rear drum assembly were very helpful.
Just watch the vid and do it! It took me exactly two hours since I was also changing out the heating element and I did it on a Friday night while having a couple tasty beers.
One tip I would give is the old grease in the bearing is very messy and I got it all over my shirt and pants - and when changing that stuff out don't lean on the front of the frame - I did and bent it out of whack a bit.
The dryer runs like new now that it's done!

Replacement of broken dryer belt and other parts.

  • Customer: David from Three Rivers MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
My wife was able to easily do the repair before I could get home from work to do it. She watched the PartSelect video on her iPad as she did the necessary steps to get the belt replaced. We only needed one glide replacement, as one was still attached and intact. We should have purchased both sets of felt seal replacements, though that wasn't as urgent.
My wife thought the repair was quite easy overall.

female part of door clasp broke

  • Customer: Tammy from St. Peters MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
All I did was push the new part into the machine! So easy!

Missing power cable cover/damaged terminal block

  • Customer: Glenn from Universal City TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
While changing power cable from 3 prong to 4 prong connection on a recently purchased used dryer I found the terminal block partially melted due to improper connectors which overheated. The bracket and cover were also missing which presented a shock hazard for anyone touching the exposed connections and there was no way to connect the strain relief. I disconnected the old 3 prong cable, removed the old terminal block, installed the new terminal block (required opening the dryer top for access), threaded power cable through bracket and fastened with strain relief leaving loose, attached the neutral/ground wires to middle terminal connection point, red to red wire in terminal block and black to black wire also in terminal block and tightened bracket and added cover.

Heating Element broke

  • Customer: brad from oklahoma city OK
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
much as described earler,
1. Removed 2 screws on back at the top and 2 on the chrome vent to access the belt and pulley.
2. Disconnected spring from pulley assembly and removed belt from pulley and motor.
3. Removed top of dryer.
4. Removed control panel.
5. Removed screws from inside dryer tumbler (all of them)
6. Removed bottom kick plate.
7. Removed 2 screws from inside panel (near tumbler) and 2 screws from bottom of front panel. Removed front panel.
8. Removed tumbler housing.
9. Removed heating element cover.
10. Removed heating element pan. (wires first)
11. Removed "bearing" by lifing it up (snaps in)
12. Cleaned and regreased "bearing"
Assembled in reverse order.

Lound noise inside dryer

  • Customer: Joseph from little Egg Harbour NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

Dryer squealed like a pig and at times the drum stopped rotating

  • Customer: charles from new holland OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
First thought the problem was a stretched drum belt or bad idler pulley. Ordered a new belt and idler assy plus spring. Replaced those items with relative ease following suggestions obtained at this site.However, problem persisted and I now suspected a bad drum bearing. Odered the bearing kit and replaced same using the following procedure.
1. Removed the cover from the back of the dryer (held in place via two phillip head screws)
2. Pushed down on the idler assy and removed the idler spring to release the drum belt.
3. Inserted flat tip screwdriver between the top panel and the dryer main body in the front of the dryer to pry the top loose from the two retaining clips.
4. used phillips screwdriver to remove the two retaining screws (one left, one right) that hold the front panel to the main body of the dryer. (about a foot down from the top of the dryer).
5. disconnected the wiring plug on the top right hand side at the top of the dryer.
6. lifted the front panel slightly removing it from the main body and placed it to the side.
7. lifted the rear of the drum to release it from the bearing bracket and removed the drum belt.
8. Pulled the drum through the front of the dryer body and moved it to an open work area.
9. Reached into the Dryer and loosened the two
bearing bracket screws with a nut driver. Here's where another pair of hands would have come in handy. Holding the ground bar on the back of the drum with on hand, reached into the dryer and finished removing the bracket screws somehow managing not to drop the tiny grounding ball (size of a BB) Removed the badly damaged plastic bracket, grounding bar, and grounding ball and set
them aside to be discarded later.
10. Used impact driver with phillips attachment to remove two of the three screws that hold the bearing to the back of the drum (these are on the inside) The third screw's head stripped out and I had a very difficult time removing it. Had it not been for that, the job would have taken less than an hour.
11. I had my wife hold the bearing in place while I started the three retaining screws.
12. My wife also got behing the dryer and held the grounding bar in place while I installed the new bearing bracket . (this kept me from loosing the grounding ball)
I just reversed the rest of the procedures to install the drum belt, drum, front panel, etc.
The dryer works like new now, doesn't squeal.
Also replaced the on/off switch knob (just pulled the old one from the stem and slid the new one on.
All Instructions for the GLER331AS2
76-90 of 392