GLEQ642AS2 Frigidaire Dryer - Instructions

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Slowly my dryer began to stop worftking. I found myself wiggling the starter knob to make it work until it completely gave up. I took the model name and number and found a video describing how to replace the starter device. it took me about 20 minutes to make the change. it only took that long because I decided to clean out the interior thoroughly with a vacuum. All in all it was very easy.

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.

After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.

The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.

Followed video that was provided!! Now I know how to get the top and front of dryer OPEN. Now I can clean interior of dryer ALSO, lots of lent!!

I followed the instructions in the videos that came with the email I got when the parts shipped. I would recommend looking at all the parts that come with the kit before you start. The video says to reuse some parts, but you have new ones. Also, after unplugging the dryer, I used a flat screw driver to pop the tabs on the 'lid' of the dryer. Removing the two screws that hold the front on was easy, and removing the front to sit aside. The flashlight is nice when you reach under the drum to get the belt off the idler pully and motor pulley. Wiggling the drum out was a little tricky but not hard. After removing the drum, I vacuumed the lint and really cleaned the inside of the dryer. Taking the screws out of the inside of the drum would be easier if you can put it up on a table or other work surface. Bottom line, I'm a girl with arthritis and did it by myself, you can too :) Dryer runs like a dream

I followed the instructions in a Youtube video that an individual made with his kids. The only hard part was removing the drum assembly, the rear drum bearing was very difficult to unseat. I had to reattach the front of the dryer to give the drum assembly more support to be able to lift the rear - but overall it was quite easy to figure out disassembly and reassembly of the dryer. There's really not that much to them.

ordered correct knob and replaced it myself.

I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.

It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

Pushed new one on

I have a washer-dryer combo unit, so the repair steps were slightly different than the repair videos I watched. (1) removed the screws at the top of the dryer and remove the top. (2) removed the front control panels and unscrewed the front of the dryer (where the door is mounted to). (3) from the back of the dryer, removed a small metal sheet to access the dryer's belt and dismounted the belt from the motor. Finally, lifted up the dryer drum and take it off the dryer. Once this done, I used the rear drum bearing kit and replaced the assembly that hold drum from the dryer back. This was a straight-forward and did not take much time. Unfortunately, the belt I purchased was a bit short, so I kept the old belt during the assembly.