Models > GLEQ2152ES0 > Instructions

GLEQ2152ES0 Frigidaire Dryer - Instructions

All installation instructions for GLEQ2152ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GLEQ2152ES0
46-60 of 313
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

THUMPING NOISE, CLOTHES GETTING STUCK

  • Customer: LT Frank from Wacissa FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
UNPLUG, LIFT TOP, UNPLUG 5 WIRES, REMOVE 2 SCREWS, PULL DRYER FRONT AWAY WHILE SUPPORTING DRUM. REMOVE OLD GLIDES, SNAP IN NEW. REVERSE DISASSEMBLY PROCEDURE

Takes multiple cycles to dry clothes

  • Customer: Pamela from Portland OR
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
I don't think it would take others as long as it took me.
I had to take the drum out to get to the limiter. And my dryer is in a builtin housing with limited space in front of the dryer - so lots of manuevers to get access.

The limiter was very easy to find, thanks to diagrams on this site. The space between drum and limiter made it impossible to get to the limiter screws without removing drum. Found very helpful drum removal instructions on PartSelect here:

http://www.partselect.com/PS1148434-Frigidaire-134503600-Dryer-Drum-Belt.htm?SourceCode=13&ModelNum=FSE748GFS0

Great site - thank you.

Dryer would not start.

  • Customer: Onmi from Douglas GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
Unplugged the dryer from electrical socket. Vacuumed lint from dryer and exit hose. Removed top from dryer. Used pliers to remove the 2 wires from the thermal limiter. Used screwdriver to remove 2 screws that held the limiter in place.
Installed the new limiter, connected the 2 wires, plugged in the dryer's electrical connection, turned on dryer, and resumed my "washday chores".

The dryer was over-heating, the vents had been cleaned to it wasn't the vent, but something wrong with the dryer. The Thermal Limiter was a cheap try to see if it would fix the problem.

  • Customer: William from Pardeeville WI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 6 of 9 people found this instruction helpful
The hardest part was getting to the part and removing it and putting it back on. The schematics that you had on your website helped us locate where it needed to go and, hopefully, that will solve our problem.

Drum guides came out into dryer

  • Customer: lloyd from celina OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Removed old guides ( some of the snap in fastners were broken off). REplaced guides by rolling drum, easy to snap in @ drum bottom each time.

Screeching noise when drying

  • Customer: David from Rockville MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

Zipper was cought between brum and cabnet

  • Customer: John from Swansboro NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Disconect power, Removed top and front of dryer.
The broken zipper was easly removed at this point. The plastic glides easly snap out and in. The felt took some more time to scrape off and clean the old glue. Glue the new felt into place and replace front and top. The parts were shiped promptly and the dryer was out of service for only three days.

Dryer would not start. When turning on, I could hear faint humming, but the motor would not start.

  • Customer: Mark from Normalville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
1) Unplug the unit.
2) Remove all screws from top of the unit except for the one in the center front that does not go through the outer casing.
3) Find the Thermal Limiter which is on the back wall near the top on the left side when looking from the front.
4) Disconnect the two wires
5) Remove the two screws that mount the limiter to the back wall.
6) Use an ohmeter to test if a current flows through the unit. If no current flows through (an open switch), then the unit will need to be replaced.
7) Clean any lint that you can at this point.
8) Use two screws to mount new Thermal Limiter
9) Reconnect the two wires to the Limiter.
10) Attach the top of the dryer case.

Missing power cable cover/damaged terminal block

  • Customer: Glenn from Universal City TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
While changing power cable from 3 prong to 4 prong connection on a recently purchased used dryer I found the terminal block partially melted due to improper connectors which overheated. The bracket and cover were also missing which presented a shock hazard for anyone touching the exposed connections and there was no way to connect the strain relief. I disconnected the old 3 prong cable, removed the old terminal block, installed the new terminal block (required opening the dryer top for access), threaded power cable through bracket and fastened with strain relief leaving loose, attached the neutral/ground wires to middle terminal connection point, red to red wire in terminal block and black to black wire also in terminal block and tightened bracket and added cover.

noisy

  • Customer: mark from clearfield PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 5 of 7 people found this instruction helpful
my motor was making noise i tried to replace the motor but could not get the blower wheel off the motor so i had to buy a blower and housing assy. also... now it works great...

broken dryer belt

  • Customer: Lee from Sunbury PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
removing was easy just open lower rear LH panel . Ordering was easy ,shipping seemed like alot? to install the new belt pop top of dryer I used a screw driver to help. remove front panel 2 screws then it also has about six clips may have to have gloves on so you do not skin your hands like I did.... lots of sharp edges. pay attention to the clips, so if they come off they will not be lost. panel will tilt slightly fwd then raise up and set aside. now you can slip the belt over the drum. I kept all the slack at the top till it was in position. the groved rubber side goes against the drum and the motor pully. then extend the spring tensioner into position . I rotated the drum a few times by hand to make sure everything was in position. replace front. check it is lined up well before forceing clips in. check felt material is properly in place, as you rotate it into position. push down top . good to go. I ran it for awhile watching everything work before placing it back in service. you may want to clean it out some while it is apart I used an air compressor and shop vac simultaniously as that seemed to work best. Wanted my son to do it as I think he had it over loaded as to why it broke? It maybe the bearings are going but it felt solid ?? I should find out in a month or so shich was which! I did not see any easy way to get to grease it. The belt was easy though pretty sure my son could have handled it!

howling dryer. Wolves in the area would howl back!

  • Customer: David A from Deer River MN
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 4 of 5 people found this instruction helpful
Waited only 2 days for part. That was with REGULAR delivery. It usually takes weeks to get out to REMOTE northern Minnesota.
Unstacked the dryer took off the top. 2 screws to open front. Pulled 3 drum mounting screws. Pulled the drum. Removed the pivot. Cleaned (blowed and vacuumed everywhere). Cleaned the pivot receptacle. Relubed the pivot with high temp lube. Removed 2 motor assy mounting screws. Screwed off the squirrel cage. Swapped the motor. Remounted new motor assy. Looped belt over drum. Remounted the drum. Closed the front. Closed the top. Opened the belt access plate on the rear. Looped new belt over the tensioner. Closed the access plate. Restacked dryer. Turned it on. Sounds like brand new. Less than 2 hours. Saved more than $800. More than I generally make an hour! Actually I saved a lot more than $800 because I probably would have had to buy both the washer and dryer stack so it could have been around $2500.
Everything I ordered arrived in 1 box and all parts are right!
Now in my spare time I need to replace the bearings on the old motor and I'll be ready for the next time, in another 10 years!

Blower wheel was raddling

  • Customer: jena from loganville GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 14 of 35 people found this instruction helpful
The blower wheel was a bit difficult, but manigable to do yourself.

heater element was broken

  • Customer: eufemio from deltona FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 8 people found this instruction helpful
I removed dryer exhaust hose.unsnapped top cover the clips are in front and exposed inside of dryer,remove 2 screws on inside of front cover and set aside. remove lower cover in back and push belt extender until belt is loose remove 3 screws on inside of tumbler. remove tumbler out the front of dryer be careful not to damage belt set aside remove ball plate by pulling up and out it will unsnap. Now remove 2 sets of wires that are connected to heater element plate remove 4 screws holding element plate in place. Since dryer was all exposed I cleaned everything out with a wet vac put back together following instructions in reverse. Good luck

drum glides worn out making thumping noise.

  • Customer: david from edinboro PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
watched video on replacing rear bearing.although rear bearing was not the part(s) i needed to replace, video instructed disassembly procedures to get to the drum glides. this was a very simple and easy to follow video. repair was a breezeand took roughly 25 minutes. the most time consuming segement of repair was vaccuuming out lint,that was 15 minutes. In future, as a preventative, i plan to remove front of machine to clean annually.
Thank you.
All Instructions for the GLEQ2152ES0
46-60 of 313