Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GLD6210L20BB

GLD6210L20BB General Electric Dishwasher - Overview

Get Parts and Repair Help for GLD6210L20BB

If you know the dishwasher repair part you need, you can browse the list of all parts on the GLD6210L20BB, or you can search by name or part description. You can also find your part by where it is located on the GLD6210L20BB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for GLD6210L20BB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.22

RACK SLIDE END CAP

This part attaches to the rails, for the upper rack, to prevent the dishrack from sliding all the way out.

$17.66

Lower Rack Wheel Kit - 8 Pack

This kit includes the 8 wheels and 8 axles.

$6.13

Recess Door Spring

$46.54

Detergent Dispenser with Rinse Cap

This part releases the detergent and rinse aid into the dishwasher.

$10.58

Door Handle Actuator

$53.87

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. This valve has a 3/8" inlet and comes with the mounting bracket.

$12.23

Middle Spray Arm

$21.36

Upper Rack Wheels - Kit of 4

This is a kit of 4.

$122.75

Lower Dishrack with Wheels - Gray

This dish rack includes the wheels.

$35.80

Lower Spray Arm

This spray arm is located on the lower half of your dishwasher. Water is forced through this spray arm by the unit's pump and motor assembly. The force of the water propels the spray arms, spraying water and detergent onto the dishes on the dishrack.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lower rack wheel was melted

  • Customer: Mark from Huntingdon Valley, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 477 of 483 people found this instruction helpful
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience. read more

The rear wheels were missing on the lower rack.

  • Customer: Teresa from Phenix City, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 462 of 466 people found this instruction helpful
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama. read more

soap door latch broken, wouldn't hold soap for later release in middle of cycle like it was supposed to.

  • Customer: James from Naperville, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 76 of 81 people found this instruction helpful
Turned off power to unit, 'cuz it has a solenoid lead to open the soap door.
Removed the phillips head screws that held the door together. The screw are located on the inside edge of the door, there are 10-12 of them.
Spearated the door shells carefully, trying not to disturb the location of the wiring in the middle of the door.

Found... read more