Models > GJC3034LB02 > Instructions

GJC3034LB02 Whirlpool Cooktop - Instructions

All installation instructions for GJC3034LB02 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GJC3034LB02
1-15 of 26
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Hot Burner Light always on

  • Customer: Gregory from Cary NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 34 of 49 people found this instruction helpful
Thermal switch is integral to element and can not be changed, must replace entire element.

Turn off power. Removed front two screws above oven door jamb and lifted the top. Removed the bracket that holds the element against the glass top and removed the element. Moved brackets from old element to new one, aligning to same numerical position and then moved wiring to new element. Slide new element under bracket and reinstalled single screw. Replaced top and screwed down. Turn on power and test .

Radiant element, 2400 watt, under Ceran glass cok top needed replacement.

  • Customer: GEORGE from NEWNAN GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 39 of 84 people found this instruction helpful
turned off power
removed ceran top from cabinet
removed element
installed new element
replaced top
powered up and was done

Bad Element

  • Customer: Michael from Howell MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 28 of 59 people found this instruction helpful
Bought new element and installed. Very simple. Used phillips
screw driver.

No heat on burner

  • Customer: paul from trumbull CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 13 of 19 people found this instruction helpful
Turned off electricity! Pulled stove out -lifted up glass top(carefully) simply removed burned out coil and replaced it with new one.

Defective Surface Burner Element - 1800W

  • Customer: Robert from Daytona Beach FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 12 of 19 people found this instruction helpful
First discount Ac from wall, then take out 2 screws on the front of the range top and lift up the top of the range surface, then while holding up the surface top take out the front burner and replaced new burner element.Let the surface top down and screw in the two screws. the surface top of the range is hinged so it would be good to have someone to hold the top up while you replace the element or use a piece of wood to hold it up,this is a piece of cake to repair. would like to thank parts select for their service. I have ordered from them before and they back up their products
Robert

Baked on sauce

  • Customer: Julie from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 8 of 10 people found this instruction helpful
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

A heat control switch was broken.

  • Customer: Barry from Wichita Falls TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 16 people found this instruction helpful
I first turned off the power to the stovetop at the breaker box, disconnected the power supply wires, removed the stovetop from the counter, placed the stovetop on a towel on the kitchen table, removed the screws connecting the glass top to the base, removed the glass top, removed additional screws holding the sheetmetal housing for the switches, opened this area and located the faulty switch, disconnected the wires leading to the faulty switch, connected the wires to the new switch, secured the switch to the sheetmetal housing and put the unit back together. It was not a difficult repair, just took a little time.

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 8 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

the burner didn't work and digital part too

  • Customer: Eduardo from Lenexa KS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 3 of 13 people found this instruction helpful
I used the digital multimeter for measure the voltage in the burner and in the digital part,I saw the electric cables

BURNER WOULD,NT HEAT UP.

  • Customer: david from cleveland TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
REMOVED TOP OF STOVE REPLACED HEATING ELEMENT ,PIECE OF CAKE.

burner knobs

  • Customer: Beverly from Buffalo Center IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very well

Center of Front Burner not heating up

  • Customer: Bob from Aberdeen NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

"Hot burner" Light always On

  • Customer: Stephanie from Phoenix AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It's easier with two people.
1 - Turn the breaker for the range to OFF
2 - Verify power is off by testing the burners and lights
3 - Remove front two screws above oven door jamb
4 - Lift the top and prop it up with the spoon, or have your helper hold it.
5 - Loosen the screw at the rear of the bracket that holds the elements against the glass top (front and rear are held by the same retainer)
6 - Remove the bad element by sliding it sideways from the retainer. Do not disconnect things yet.
7 - The burner has numbers around the edge. Move brackets from old element to new one, matching the numbers. Then move wiring to new element. New burner may have a single connector where old one had 2 and a jumper. If so, ignore jumper.
8 - Slide new element under bracket and reinstall the screw.
9 - Lower the range top and re-install the screws.
10 - Turn on power and test.

1200 watt r/rear burner element has an opening in the elementg

  • Customer: Jayson from Cape Coral FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

burner not as hot as it should be

  • Customer: Joel from Dillon SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.
All Instructions for the GJC3034LB02
1-15 of 26