GJC3034GQ0 Whirlpool Cooktop - Instructions

looked on internet on how to remove top. an easy fix after watching video

First I found a YouTube video for Maytag Range Repair – How to replace the Surface Element with Limiter - 6" - 1200W

The steps are very easy-
1. Open oven door and locate and remove 2 screws holding top cook surface. These are located near the top inside edge

2. Lift surface cook top and then remove 4 screws holding this section to the cook top. This may require 2 people but I was able to hold the cook top and loosen the 4 screws myself. Then put the cook top aside.

3. Take a photo of the element being replaced for wiring connections.

4. Removing the wiring and element holding clips was very easy. I used needle nose pliers for both

5. The clips have to be removed from the old element and put on the new one. Place them in the same locations

6. Make sure to reconnect the wires to the same pin locations. The replacement element I had the red (hot) wire pin 2b was in
A different location so I had to use the extension wire supplied with the new replacement element

7. Put everything back together in reverse order.

Easy peasy, took me about 40 minutes to complete the entire replacement and have it back in place working.

The new element wiring placements were totally different from the old element. Lucky for me the lettering printed on the terminals for each pole was the same as on the old one. It was just a matter of matching up each terminal pole lettering. The instructions that came with the new element were of no help at all. Youtube was my best helper.

Verified via ohmmeter that one of the two burners was open and not working. I also tested the switch and that appeared to be working okay. I then took out the old unit and compared it to the new one, and found that they upgraded the new unit. I followed the instructions to match the labeled parts and move the wire to the newer location of that. i.e the old one had 2B and 2A at the top and 1B and 1A at the bottom. The new one had 2B and 1B at the top and 2A and 1A at the bottom. It did come with wire extenders and insulated tubes on top of them, and extra to cover additional. After a couple of tries, I decided which wire I needed to use on which (small connectors to match small, and large to match large.) In a second try I decided to flip it over to have it face up instead of down. Overall, it worked out very well, and I was very pleased when I did the power up test and everything worked as desired.

Very easy just followed manufacturers instructions.

I decided NOT to crawl under my stove top to find the correct model no. of the unit, as recommended in the Help section of the website. Instead I just guessed. It arrived, and of course didn;t fit. So I crawled under the stove top, got the correct model no., and instantly found the correct part to order. Part Select instantly honored my request for a refund on the first part and the correct part is on its way. So I ended up paying two delivery charges instead of one. LESSON LEARNED.

Followed the instructions in the video provided by PartSelect, which was very accurate. They only problem I have encountered is that the wiring from the old element compared to the new element do not match up 100%. I had to call Whirlpool today and schedule a Tech to come out and see if they can resolve the problem. Right now, when the burner is turned on, both the inner and outer elements turn on.

Removed module replaced radiant element very easy repair.

My dual zone burner would trip my breaker anytime i tried to turn it on. All the other burners would work fine. I searched online and found a way to test my burner, which was shorted or grounded out. I purchased a new burner from the site...It was as cheap or cheaper than other sites. It showed up a few days quicker than i was expecting..I also replaced the switch to the burner, just as a precaution and to save time since i already had the top glass off of my burners....EASY JOB!

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Dual Burner switch was a replacement and not the same as original - instruction sheet gave excellent replacement instruction with color coded wires and numbers too follow, 6" switch was same as original so no problem with either switch replacement - stove now works like it was new.

Removed glass surface and identified existing wiring (sketch, photo, schematics) before disconnecting and removing it. Installed the new switch and connected the wires using the supplied wiring instructions as well as my sketch and schematics. Appreciate that the new switch came with wire extenders and shrink tubing. Had to use both of them.
Replaced the glass top and installed it back into the counter ,Turned on the circuit breaker and everything worked perfect. Just want to mention that I am extremely satisfied with PartSelect service. It is second time I ordered cooktop part. The delivery is prompt and the parts work as required

Removed burned out burner, replaced new burner tested works fine

Thank you. Have been looking in stores for knobs to no avail.

I used a nut driver to take the module apart. When I discovered the problem I simply threw the module out but kept the ceramic top and then ordered a new stove top. The burners would be a snap to install if the clips that secure it in place had not ALL broken off. All you do is pull the wires off with a pair pliers and set the new unit in place and reattach the wires. All that would be left would be to reattach the ceramic top and set the module back into place on the stove top. The modules were discontinued and no longer available any place. Believe me I tried. The delivery to me from Parts Perfect was very quick and without any hassles. I had no problem returning the burner. I would recommend these people any time.