Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GI15NFRTB4

GI15NFRTB4 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for GI15NFRTB4

If you know the ice maker repair part you need, you can browse the list of all parts on the GI15NFRTB4, or you can search by name or part description. You can also find your part by where it is located on the GI15NFRTB4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for GI15NFRTB4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$87.13

Condenser Fan Motor Kit

This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move...

Order within the next 1 hr and 42 mins and your part ships today!
$62.23

Recirculating Pump - 60Hz

A recirculating pump is used with standalone ice cube makers. It circulates the water over the top of the evaporator plate, which produces a layer of ice that is then broken down into ice cubes. If you notice that your ice maker is no longer producing ice or there is no water flowing over the cooling plate, this could be due to the recirculating pump not working. Be sure to keep the pump clean and free of build-up. This pump is 5.75 inches in length, 4.75 inches in width, 4.25 inches in height and weighs 0.81 lbs. This is a genuine OEM appliance part that comes directly from the manufacturer.

Order within the next 1 hr and 42 mins and your part ships today!
$137.02

Ice Cutter Grid Complete Assembly

If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker, and...

Order within the next 1 hr and 42 mins and your part ships today!
$36.88

Thermostat, Bin

This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce more ice or activate shut-off. The bin thermostat may need to be replaced if bin is overfilled, underfilled, or not producing ice. Thermistor can be tested with an ohm meter. This part is made of plastic and metal, and is white in color. This is an authentic part sourced from the original manufacturer.

Order within the next 1 hr and 42 mins and your part ships today!
$3.02

Screw

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an ...

Order within the next 1 hr and 42 mins and your part ships today!
$15.95

Switch, Plunger Grid/Light

The purpose of the light switch in your refrigerator is to automatically turn on the light when the door is opened. If the light does not come on automatically when you open the door, the contacts inside the light switch may be burned out, meaning it is time to replace the switch. This package contains both the new light switch and a small plastic spacer. To complete this repair, you will need to remove the control panel section of your refrigerator. The only tools you will require for this repair are a 1/4-inch nut driver and maybe a small flat blade screwdriver. Be sure to disconnect the power source from the refrigerator before completing this repair.

Order within the next 1 hr and 42 mins and your part ships today!
$77.73

Pump, Drain

Order within the next 1 hr and 42 mins and your part ships today!
$50.19

Temperature Sensor

This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches wide, and includes the necessary wiring connector. You will find this part located in the water pump area of the ice cube maker. The function of this part is to determine the water level within the water reservoir. Once the water level reaches a certain point, the sensor will signal the controls to fill the reservoir.

Order within the next 1 hr and 42 mins and your part ships today!
$35.13

Ice Cutting Grid Wire

There is approximately 10' of wire. Note: 2 kits are needed to replace both directions.

Order within the next 1 hr and 42 mins and your part ships today!
$17.80

Drain Fastener Cap

This is a drain fastener cap and is used in conjunction with your freezer/refrigerator. This model is almost 1.5 inches in diameter, half an inch thick, and is white in color. This piece will fasten to the bottom of the water pan in your ice maker. It keeps the water in the water pan from leaking into your appliance. If your drain cap is loose or broken, the liquid from the water pan will empty and you will have no ice or very thin ice. Make sure when replacing this part to secure the drain cap tightly.

Order within the next 1 hr and 42 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Seven year old condenser fan was making noise when it was running.

  • Customer: Josue from Jacksonville, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 176 of 182 people found this instruction helpful
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harne... read more

Fridge made noise and the center post was HOT!

  • Customer: David from Jefferson City, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 44 of 46 people found this instruction helpful
We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.

For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must order a motor/fan, do... read more

Broken light switch

  • Customer: Randy from Hays, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 58 of 97 people found this instruction helpful
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is alm... read more