Models > GI1500XHW9 > Instructions

GI1500XHW9 Whirlpool Ice Maker - Instructions

All installation instructions for GI1500XHW9 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the ice maker repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GI1500XHW9
1-15 of 76
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Seven year old condenser fan was making noise when it was running.

  • Customer: Josue from Jacksonville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 94 of 99 people found this instruction helpful
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow.

Lack of frequent cleaning resulted in pump failure due to buildup from hard water mineral deposists

  • Customer: Louis from Cheyenne WY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 38 of 39 people found this instruction helpful
This ice maker is really a Kitchenaid appliance.

1. Remove all ice and drain water pan by removing drain cap.
2. Disconnect waterline and unplug ice maker
3. Set icemaker on a work bench unless you like working on your knees, head down.
4. Remove flip out chute and ice scoop bracket.
5. Remove water pan by removing thumb screws
6. Remove single 1/4" head cap screw that holds plastic cover over pump.
7. Remove discharge hose from pump. Pull clear plastic 1/8" diameter water supply line from notch in left edge of pump base.
8. Remove three cap screws holding pump. Two are visible. The third one is behind the pump and requires an 8" extension on the socket.
9. After the three screws are removed the pump drops down. The electric connection must be unplugged. Pinch the tabs on either side to release the plug.
10. Reverse procedure to install new pump. Unless you have really small hands or love being frustrated, don't bother to reinstall the third screw that is behind the pump. The pump stays in place just fine without that screw.
11. After reinstalling the icemaker, clean thoroughly by washing all inside surfaces with a strong bleach solution.
12. Run a cleaning cycle with one quart of strong bleach solution in the water tray. At the conclusion of the cleaning cycle, drain the water tray. Place unit into service. DON'T FORGET TO CLEAN REGULARLY. If the water supply is not chlorinated molds and algae will develop in recirculation hose.

Fridge made noise and the center post was HOT!

  • Customer: David from Jefferson City MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 25 of 27 people found this instruction helpful
We have a side-by-side fridge/freezer and we experienced a hot center post (where doors come together) and the fridge made loud noise. Also, the (old) fan motor would start, but then quit, so our issue was the motor.

For me the repair was very easy, but for an unexperienced person it may prove to be difficult. If you must order a motor/fan, do NOT order the metal fan as a plastic fan comes with the motor. What's strange is the new motor is different than the old one, but it still mounted without any required modifications. I did NOT use the wire harness that came with the motor either as it was different too, but my old one was still good.

Check all of your parts as my fan had a cracked blade, but I used "superglue" and it's fine now.

Fridge stays cold and my wife had to lower the temperature in the fridge as she was blasted by the cold!

old condenser fan motor shaft was loose and it made the spinning fan blades shake and cause noise

  • Customer: Christopher from Snow Camp NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 19 of 20 people found this instruction helpful
The procedure was straightforward. I removed the cardboard backing on the lower back of the refrigerator to expose the fan unit. I then undid the electrical harness at the fan. I then removed the three screws securing the fan motor to the metal bracket. This is the hardest part in that I had to reach through and get to the screws with my small tools. I then removed the old motor and blades and placed the new motor and blades. Again, a bit tricky trying to get the three screws mounted into the bracket...small tools and hands helps. After that I used the electrical harness supplied with the kit to plug into the new motor and I was done.

fridge made a loud growling noise when running

  • Customer: Bob from Mandan ND
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 13 of 18 people found this instruction helpful
removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there

Grid Assembly had a broken wire and would not separate the ice sheets into cubes

  • Customer: Brad from Bakersfield CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 14 people found this instruction helpful
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a couple of hours

the top wire on the cutting grid broke and thus no longer cut the ice. It sat on the wire until the ice melted, depositing no ice into the bin

  • Customer: Sherri from Ada OK
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 10 of 11 people found this instruction helpful
I removed the cutter grid and unplugged the light bulb and wire heating plug ins. I slid the front cover plate off the cutting grid and loosened the screws on the front of the cutter grid and unthreaded the broken, top grid wire, leaving the bottom wire in place as it was in tact.
I then threaded the new wire through the cutting grid frame starting in the center and threading right and then left. While the threading was not difficult, the wire was easily kinked. The process up to this point was only 15 minutes or so.

Once it was completely threaded, I worked for a couple of hours trying to smooth and straighten the wire so that is was somewhat taut and straight enough to create symetrical ice cubes.
My frustration came in pulling on the wire from the center point to each outside ending point where it was to be wrapped around the screw and the screw tightened back down. The wire was fragile enough that it would break, by the time I was finished I barely had enough wire left to touch the screw let alone hook around the screw.
After 3 or four days of successful opperation, the grid quit cutting again. As I took it apart, it was obvious that the weight of the ice was enough to pull the wire, that was already too short, away from the screw. I refastened it again, but think it is unlikely to hold.
If it won't hold, I would be hard pressed to purchase another wire. I may bite the bullet and purchase the entire grid mechanism with the wires already installed. Even though the cost of the entire grid mechanism is $200 more than the purchase of another wire, it may well be worth the ease of installation!

The water was not circulating over the cold plate

  • Customer: Benjamin from Chesapeake VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 10 of 13 people found this instruction helpful
I removed the cutter cover in the front of the ice maker (3 screws), than removed the circulating pump cover (1 screw). Remove the drain tube from the cover before removing the cover from the icemanker. The drain tube is removed by pulling straight down and twisting. Remove the circulating pump, utilizing the 4 inch extension (3 screws). Reinstalled all in reverse.

Note: install a plug in the drain hole in the bottom of the ice maker (paper towel etc). I dropped a screw on the installation and it fell in the drain hole. It did not impede the drain flow. It has now found a new home.

Motor was noisy

  • Customer: Rick from Florence SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 10 people found this instruction helpful
I removed 4 screws holding the motor mounting bracket and removed the assy from the unit. I then removed 3 screws holding the motor to the bracket. I put the fan blade on the new motor and reattached the motor to the bracket. I plugged in the wiring adapter to the motor and reinstalled the bracket in the unit with the 4 screws. Finally I attached the unit wiring connector to the motor.
It was relatively easy.

Circulation pump failed. Replaced same.

  • Customer: John from Covington LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 8 of 9 people found this instruction helpful
Unplugged ice maker from power source. Removed water reservoir using wing nut driver. Removed pump cover using nut driver. Removed water hose from pump discharge. Removed wiring harness from pump. Removed small water fill hose from pump bracket. Removed 3 screws holding pump assembly using nut driver. Replaced pump in reverse order. Plugged in ice maker and watched it begin to fill with ice within the hour. A very straightforward repair. Saved myself about $500 compared to the estimate that Sears gave me.

Ice maker started leaking water from the water valve that inputs water to the appliance.

  • Customer: william from etowah TN
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 8 people found this instruction helpful
removed the front cover below the compartment door,removed the 2 screws holding the valve to the case and removed the water lines from the valve.The process was reversed to install the new valve.

open drain hole

  • Customer: James from Redding CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 8 people found this instruction helpful
In pre-replacement of the circulation pump, i had read a story about how to make sure you cover the drain hole to prevent hardware from falling down it. Well I followed the instructions in doing so by covering the hole with a paper towel. After removing the pump i noticed some build up behind it. So like any other person i cleaned it up, and i just happened to use the paper towel covering the hole. Im sure you know what im going to tell you next. When replacing the pump i dropped a screw and yes down the drain it went. After a few laughs between my boss and I, I had to share this. When you block the drain with something leave it THERE until the job is done.

Dead condenser fan/motor

  • Customer: Drew from mountville PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 8 of 11 people found this instruction helpful
Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.

Water began to leak under the refrigerator. Source looked like it was coming from control valve suppling water to ice maker and water dispenser.

  • Customer: jesse from hacienda heights CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

ice maker made ice but pump ran too much

  • Customer: David from Collierville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 10 of 18 people found this instruction helpful
First I removed the front door by removing the screw on the top hinge. Then removed the upper hinge plate. This allowed removal of the top corner retaining screw. Removed screws at three other top corners. Now I could raise the top at a 45 degree angle to remove the controller cover. The controller was connected with several wire clips and held in place with two screws. Quick swap out and reverse order completion. Ice maker works like new!
All Instructions for the GI1500XHW9
1-15 of 76