GI1500PHW7 Whirlpool Ice Maker - Instructions

I pulled the refer from the wall, disconnected the power and removed the cardboard cover at the base. Using a vacuum and compressed air, I cleaned it thoroughly.
I used a screwdriver to lift the locking tab on the 3-wire connector and removed it. The best way to get the three bolts off was with a 1/4" drive ratchet and go to the std nutdriver handle when they were loose. The fan came out carefully with the blade. I removed the blade nut with flat nosed pliers, cleaned it and placed it on the new motor. I replaced the motor and installed the screws. On a do-over I would install onew screw in each hole at least halfway to get the threads started/ threaded. After that the connector slipped in and I spun the blade to check for interference. The blades can be slightly bent, but use of nut tension can also slightly adjust fan alignment as it's tight to the housing.
That's it

My husband took the old motor out by taking the screws out. Then, he unplugged the fan. We searched your site for the part. With the pictures on the site, we were able to match the motor exactly. The delivery was really fast. When we received the part, he installed the fan and plugged in the power connector. We have replaced refrigerator fans before but anyone can do this with no experience. Just follow the instructions and you're all set.

I replaced the bin ice sensor with the new one from partselect.

remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

Removed the grid. Removed the existing top to bottom wire. Restrung the grid with the new wire. Then, it cut ice just fine-better than new. Note: wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.

Disconnected both water lines and two mounting screws. Installed new water lines and water valve. No problems at all. Ordered the valve on a Monday and received it the next day. Even though i chose FedEx ground. GREAT SERVICE! I am a technical service manager and I always give credit to company's with great service. In fact, I have sent your website link to our management team to show what our website could be for our customers. Easy to find part numbers, pictures of the part being ordered and ease of use. World Class support.
Kindest regards,
Dave

Removed back panel and removed the motor put new quick disconnect on and tapped the mounting holes. Removed and cleaned fan blade from old motor and put on the new motor. Mounted motor plugged it in and replaced panel.

Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called parts select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200. 00--Very happy with parts select service--plus I had a misunderstanding with my credit card and john at parts select was very helpful --not their fault--excellent company

The post I read said start at the middle and work your way out towards the left and right. This was incorrect. All I did was secure one end to the torx screw and tighten it down. I then slowly pulled the wire as tight as I could around each insulator, going slow so as to not kink the wire (very easy to do). Once I was at the other torx screw I used a pair of linesman plyers to gently tug each wire tighter, I needed an extra pair of hands to hold the grid down. Once everything was tight I wrapped the last torx screw and tightened. Here's what no one is saying, you will not get the wire as tight as it originally was but that's ok. After I got everything reinstalled the ice maker is making ice like a champ.

Water was not being drawn from the reservoir to the evaporator plate, so I concluded that the recirculation pump had failed. I first unplugged the machine from electrical power. To improve access to the pump, I removed the cutter grid using a nut driver and squeezing the electric connections to separate them. I also removed the reservoir, first removing the drain pipe by pulling it downward and the using pliers to loosen the thumbscrews until I could turn them by hand. I then thoroughly cleaned both the cutter grid and the reservoir to improve performance once the repair was done. The pump is covered by a solid plastic screen attached by just one nut, which is removed easily with the nut driver. The pump itself is attached with three screws which are easily removed with the nut driver and by an electrical connection which loosens by squeezing. Indeed, Upon examination, i found that the pump shaft was stuck solid and did not turn freely, explaining why it did not work. Replacing the pump, reattaching the three screws and reattaching the electric connection was pretty easy except for the right rear screw behind the pump which was hard to reach to guide the screw without a trick up my sleeve. The trick was to wrap scotch tape around the screw and the nut driver so that I could guide the screw one-handed. Once the screw threaded through a few turns, I jerked back the nut driver, pulling the tape off the screw. I then removed the tape from the nut driver and continued to tighten that screw and the rest, and then reattached the electrical connection. I then reattached the screen, the reservoir and the cutter grid, then plugged my machine back into the electric circuit and was pleased to watch it hum back to life, good as new and performing better than it was before the pump had failed.

removed broken wire, replaced with new wire and screwed the 6 tensions screws to tighten the grid wire.

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

Replaced the assy. But, I would have been happier if you sold just the wires. I could have replaced the wires at a much lower cost and may have taken less than an hour to replace the wires.Still happy - the ice maker works.

The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years.