Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GHW9400PW4

GHW9400PW4 Whirlpool Washer - Overview

Get Parts and Repair Help for GHW9400PW4

If you know the washer repair part you need, you can browse the list of all parts on the GHW9400PW4, or you can search by name or part description. You can also find your part by where it is located on the GHW9400PW4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for GHW9400PW4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$31.92

Door Handle

This handle may appear white, but is light gray in color called Platinum.

$110.36

Bellow

This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub. Clamps are not included. NOTE: Must order clamps separately, if needed.

$24.42

Baffle, Basket

This part moves the clothes around inside your dryer/washer and helps to direct the flow of hot air during the drying cycle. Sold individually.

$73.96

Door Lock Latch

This part is used on front load washers and includes the interlock switch assembly.

$152.29

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$17.95

Control Knob

This knob is light gray and is used on platinum-colored models. Sold individually and accepts a D-shaped shaft.

$50.30

Water Inlet Valve

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

$37.80

Flowmeter

This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.

$42.39

Shock Absorber

Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles.

$2.76

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken plastic washer door handle

  • Customer: dave from woodway, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 510 of 513 people found this instruction helpful
Just required removal of two screws, placing the new handle and reinstalling the two screws. Easiest repair I've ever done! read more

Bellows were moldy, needed to replace

  • Customer: Franck from Annandale, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 284 of 303 people found this instruction helpful
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached... read more

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 190 of 196 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more