Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GHW9300PW4 > Instructions

GHW9300PW4 Whirlpool Washer - Instructions

All installation instructions for GHW9300PW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9300PW4
106-120 of 276
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellow leaking water

  • Customer: Eric from Vacaville, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
Removed the outer spring with pliers. Pushed the bellow into the drum. Loosened the clamp on the bellow with a stub nose screwdriver. Removed the bellow. lined bellow up with soap fiting. Reversed procedure to reinstall.

Door habdle broken

  • Customer: Steven from Hopewell Junction, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed screws from broken door handle, placed new handle, replaced screws. Couldn't be easier

Broken door handle

  • Customer: Sue from Hanover, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I removed both screws form the broken handle.
I then removed the rubber strip and replaced it on the new handle. I put the 2 screws back in and I was finished.
I did it all myself without the help of my husband.

Old handle craked in two.

  • Customer: James from Davie, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
After an effortless process with PartSelect with locating, purchasing and receiving the replacement handle in three days, I removed the broken handle by removing two star type screws and removed the broken handle. I placed the new handle in the appropriate location and reinserted the two screws, tightening same. DONE. I will not hesitate to use PartSelect again in the future as the service provided is as great as thier webpage indicates they are. A wonderful shopping experience from beginning to end.

broken door handle

  • Customer: linval from raleigh, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
removing the old srews was a little difficult but once it was done it was much easier to replace the new product.

Tear in door seal

  • Customer: sean from Palm Coast, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 3 of 8 people found this instruction helpful
First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.

  • Customer: Keith from Amherst, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

broke the handle off of our front loading washer...

  • Customer: michael from yorktown, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Using just a screwdriver it took less than 5 minutes to repair...way too easy! Voila I was back to doing laundry...guess that makes me happy? Back in the day I would have just bought a new washer because I never realized how easy some repairs are...and I now have a happy hubby too!

Control knob broke - because entirely plastic, turning interior metal selection rod

  • Customer: Patricia from Brentwood, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Pulled off the broken knob. Fairly disgusted with Whirlpool for not bothering to put a metal / aluminum sleeve inside to avoid the exact breakage I experienced. Part Select, however, had the part, got it to me exactly in the time frame I asked for and it was the correct part. I would definitely use Prat Select for any such need.

Washer posting a f6 error

  • Customer: Robert from Salt Lick, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 27 of 81 people found this instruction helpful
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

knob broke off

  • Customer: Renaldia from Cornelius, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
easy as pie - ordered part. arrived in a few days and popped it back on. easy as pie. great service, quick! will definitely return to buy other parts!!!

broken latch

  • Customer: Hector from Richmond Hill, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 3 people found this instruction helpful
Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

door handle broke

  • Customer: BRIDGET from LINCOLN, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
removed the two screws. screwed on new handle. very, very easy.

Handle broke

  • Customer: Larry from Taneytown, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced handle

Broken door handle

  • Customer: Terry from Ashland, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed 2 torx screws, removed broken handle, put the new handle in placed and re-installed the screws....about 2 minutes.
All Instructions for the GHW9300PW4
106-120 of 276