Models > GHW9300PW4 > Instructions

GHW9300PW4 Whirlpool Washer - Instructions

All installation instructions for GHW9300PW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9300PW4
256-270 of 275
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dispenser drawer handle broke

  • Customer: Barbara from Treasure Island FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
it just snap on in 5 seconds, incredible, can't believe it was so easy, the washer is so old I thought I will have problems fitting it in.

Door handle cracked

  • Customer: Jan from Jesup IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the two screws, removed the cracked handle, replaced with the new handle, put the two screws back in. 2 min. repair and I didn't even ask my husband for help. Simple!!!!

pump wouldnt drain

  • Customer: Edward from Dayton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
removed three screens on lower front panel removed hoses from pump after opening drain/filter to remove water slid pump forward and out unplugged pump wiring harness reverse to install

Front loading washer would collect water in the tub after use.

  • Customer: Chris from Prattville AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Disconnected the water supply lines. Removed four screws holding the top to back frame. Removed the top. Disconnected the electrical valve connections. Removed the valve set mounting screw. Removed the valve set and replaced. Reversed the steps above for installation.

Handle had cracked and broke off.

  • Customer: Susan from Danville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed what was left of the old handle, was attached with 2 screws. Used the same screws and attached the new handle. Easy as that. Less than 15 minutes.

Kept getting F2 code and washer wouldn't drain

  • Customer: Janet from Sutton WV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the front panel below tub and above pedestal off washer. Removed pump and found coins in the strainer. Removed them thinking they may be causing the problem. Put everything back together and tried again. Washer still wouldn't drain. Unplugged it and ordered a new pump. Installed pump after removing the plug and draining water from washer. Replaced pump with new one and washer works like new.

Easiest $300 I've ever saved!!!

  • Customer: Rusty from Pascagoula MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Part was $150 and the going rate to replace the pump by a repair person is $300=$450. This was super easy and took about 15 minutes, including draining the old pump with my wet vac!! I messed around witht he old one trying to clean it, etc for several weeks because I'm cheap and didn't want to spend the $150. SPEND THE MONEY AND DO IT YOURSELF.

need a star srew driver to install

  • Customer: amilee from housotn TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The installation requires a star shaped screw driver to remove the existing the screw holding the door handle. The same screws must be saved and used to install the new handle, which does not come with new screws. So, you do not want to strip the screws removing. Plan ahead with the correct screw driver- you can determine what is needed by looking at the screw head and purchasing an appropriate tool. My handy neighbor installed my new handle, but the screws can no longer be removed should I have to replace the handle a second time. The entire time to remove and install took less than five minutes.

Broken door handle

  • Customer: Harold from Temecula CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws and removed the broken handle. Positioned the new handle, replaced the screws. Admired my repair.

The door handle just broke off

  • Customer: Barbara J from Hackettstown NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I used a phillips head screw driver, however the heads of the screws were not phillips head, they were some other kind of head I have never seen.

Water was running into machine when it was off!!!

  • Customer: Lon from Cadet MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Of course the machine was not plugged in & water valves where off. I took water hoses off. Then i took 3 screws off the back of lid & slid lid back & lifted it off. I then unplugged two wires going to valve. I then took water hose going to valve off. Last there is one bolt holding valve to machine & in the mechanic industry we call this bolt a star head, so it was a good thing I had this tool. So if you do this repair you will have to get this tool. This job is easy to do & Part Select was 100% on my order & shipping! I will order again when something brakes again !!! Thank's

Broken door handle

  • Customer: Raymond from Lincoln MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed two philips head screws, took off old handle and replaced with new. Fastened with two philips head screws. Took 60 seconds from start to finish.

One drum baffle broke off drum

  • Customer: Patrick from Maxwell IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It took less time to repair than it took to get new baffle out of the packing sleeve. Set it in drum and snapped it in place. Took about 5 seconds.

Washer would not drain at all. Impeller spun on shaft.

  • Customer: Jeffrey from Marshfield WI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

The door handle on my washer broke off after pulling on it too hard

  • Customer: Jim from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The handle is set with two screws (that don't come with the replacement handle so make sure to save them when you take the old handle off). They use the 6 point screwdriver but a regular flathead screwdriver will work - a phillips won't. Take the old screws out, put the new handle on and screw it back in using the old screws. EASY
All Instructions for the GHW9300PW4
256-270 of 275