Models > GHW9300PW4 > Instructions

GHW9300PW4 Whirlpool Washer - Instructions

All installation instructions for GHW9300PW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9300PW4
241-255 of 275
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Won't spin

  • Customer: turbo trucking from mio MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Replaced water pump

Bellows stained

  • Customer: Thomas from Chesterfield VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

a drum baffle snapped off in my front loading washer

  • Customer: Leslie from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very simple repair. Lined up the baffle tabs with the drum slots. Pushed the tabs into the slots, pulled the drum baffle towards the opening of the wahser until it seated. You will hear aclick.

Door handle broke off

  • Customer: Nancy from Ventura CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the two screws from the old handle and screwed on the new handle.

The latch was broken so that the front door wouldn't close.

  • Customer: Jennifer from Staunton VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

broken control knob on dryer

  • Customer: Diane from Suwanee GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Husband out of town, house full of company (all women) and the dryer breaks. Yikes! Your company got the part to me so very quickly, I replaced the knob in minutes and all the women got to do their laundry. Happy happy group. Thanks!!!!

Water flow leaking when machine off

  • Customer: Niel from Twin Falls ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Greatest difficulty was positioning machine to get at rear. Disconnected inlet hoses. Removed rear 3 screws to remove cabinet top. Removed rear holding screw to inlet valve. Removed two electrical connections to inlet valve. Disconnected inlet valve from interior hose. Reversed process to install new inlet valve.

light was out of the ice machine in front and a shelf in the door broke.

  • Customer: Marge from Ortonville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
it was very easy. the shelf snapped right into place and the light went right in. also, the handle on my Whirlpool washer was broken and a replaced it with a screwdiver. the parts came within two days. Excellent service. Thanks

Tub would slowly fill up with water when not running

  • Customer: Danny from Piggott AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy. It took 15-20 min to replace the valve at the most. Three screws on the back and the top comes off. The valve is right there on top. Undid water hoses and then one screw and one clamp to remove the valve. So simple and problem resolved. I also took this opportunity to replace the water hoses (they were over 7 years old) since I had to take them off anyway.

Front bellow moldy

  • Customer: James from Hopewell NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed video, Slowly. Was easier then I expected. Everything fit perfectly.

Broken drum baffle

  • Customer: LISA from SEIAD VALLEY CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Did it myself, found the model # from your website, received the part, it slid right on,yay, no more tears in my sheets!

Washer would stop at different times with code FH

  • Customer: David from West Chester PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the three small sheet-metal screws holding the washer top to the frame and slid the top aft and laid it on the floor. Then I took fine sandpaper and cleaned the plug contacts from the various components connected to the main control board. After five years or so I have found that most copper connectors will corrode and prevent electricity from flowing properly. That did not correct the problem. I checked the flow control device and it appeared clear and not binding. Then I pulled the drain pump filter and it was clear. I could hear the water pump running and the water flowing out the normal rubber hose. But the washer would stop three or four times during a wash cycle. Pressing 'RESET" and "START" would start the washer again. At the end of the cycle my wife noticed there was water in the washer tub. It had to come in via the water control valve. This is the valve you screw the hot and cold water hose into. It is a ice blue color and held in by one screw. I unscrewed the two hoses and removed the one screw. Then I had to slip the black supply hose from the valve leading to the flow meter. I disconnected the four electrical connectors and installed the new valve and found the screw hole did not align with the screw hole in the washer frame. I used a eighth-inch metal drill and drilled a new hole which lengthened the slot that the mounting screw normally went through. After I re-connected the hot and cold water lines to the valve I turned the water back on and put the top back on the washer. The washer worked like new. No stops. I did notice before changing the valve the water would flow into the washer tub like beer coming from a tap. After installing the new valve the water flowed in at three times the rate like a garden hose.

Broken Handle

  • Customer: Irving from Linden NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the 2 screws, broken pieces. Put new handle in place with the screws, all done!

broken part

  • Customer: steven from ellensburg WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
easy fix

Washer shook and made noise during spin cycle.

  • Customer: Homer from Windham NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.
All Instructions for the GHW9300PW4
241-255 of 275