Models > GHW9300PW4 > Instructions

GHW9300PW4 Whirlpool Washer - Instructions

All installation instructions for GHW9300PW4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9300PW4
211-225 of 275
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Lock Latch Broken Inside

  • Customer: Chris from North Reading MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy repair, once I read the reviews and watched a couple of you tube videos. I just released the band holding the gasket in place, pulled it back, unscrewed the latch and installed a new one. Less than a 10 min job. I am glad I found this web site, thanks guys!!

The two attachement supports for door handle completely broke off.

  • Customer: Samuel from Fresno CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the brokern door handle attachment support screws off with my power drill in less than 10 seconds and intalled new handle in 20 seconds using the same power tool. Washer was ready to go.

The washing machine wouldn't drain

  • Customer: Ann from Algonquin IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!

Broken latch on front of washer

  • Customer: Brenda from Citrus Heights CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.

Bellows were moldy and underneath had mold

  • Customer: Charles from Murphy NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation

Door handle was cracked and had to be replaced

  • Customer: Kevin from Beaver PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The part was the right one, so it consisted of 2 screws out and two screws in. 3 minutes total. I needed to use an Allen wrench instead of a screwdriver, as was advertised.

Door handle broke off in two.

  • Customer: Melissa from Searcy AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed old pieces and used these screws to attach new handle. Easy!

Old hinge was worn and sagging.

  • Customer: Jason from East Quogue NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easily took the old door off of the dryer unit then removed the hinge bracket and replaced it with the new part.

motor control

  • Customer: EDGAR from DALLAS TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

door lock broke

  • Customer: vicki from westhope ND
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

Clean Water found in washer after it was used. Usually the day after it was used last

  • Customer: Nestor from Revere MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconected washer, disconected water lines, Removed top cover. Removed screw holding valve, disconnected 2 connectors for valve put everything back together

Broken knob

  • Customer: Aqua View Pool from Naples FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The dryer is in a walkway from the garage to the kitchen. One of my boys accidentally brushed up against the knob and it broke off.That happened on a Tuesday night around 9pm.I got on line that night and ordered the part and it arrived onThursday. It almost seemed impossible. That's why I am writing this review.

Water leaking into tub.

  • Customer: Larry from Tehachapi CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Too easy. It took longer to pull the washer away from the wall and disconnect it (hoses, etc.) than to R&R the water inlet valve.

hole in bellow

  • Customer: FAYE from ZEBULON GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

torn bellow

  • Customer: donald from Stanwood WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
repair was a cake-walk with the video there to help.Thanx
All Instructions for the GHW9300PW4
211-225 of 275