Models > GHW9300PW4

GHW9300PW4 Whirlpool Washer - Overview

Get Parts and Repair Help for GHW9300PW4

If you know the washer repair part you need, you can browse the list of all parts on the GHW9300PW4, or you can search by name or part description. You can also find your part by where it is located on the GHW9300PW4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for GHW9300PW4 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$22.59

Door Handle

This handle may appear white, but is light gray in color called Platinum.

$82.92

Bellow

This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub. Clamps are not included. Must order clamps separately, if needed.

$23.12

Drum Baffle

This part moves the clothes around inside your dryer/washer and helps to direct the flow of hot air during the drying cycle. Sold individually.

$137.11

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$73.55

Door Lock Latch

This part is used on front load washers and includes the interlock switch assembly.

$17.21

Control Knob

This knob is light gray and is used on platinum-colored models. Sold individually and accepts a D-shaped shaft.

$13.64

Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.

$47.68

Water Inlet Valve

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

$4.65

Touch-Up Paint - White

$3.76

Door Hook/Strike

Attaches to door lock mechanism.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken plastic washer door handle

  • Customer: dave from woodway WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 471 of 473 people found this instruction helpful
Just required removal of two screws, placing the new handle and reinstalling the two screws. Easiest repair I've ever done! read more

Bellows were moldy, needed to replace

  • Customer: Franck from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 215 of 231 people found this instruction helpful
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached... read more

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 107 of 111 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more