GHW9200LW0 Whirlpool Washer - Instructions

The design of the baffle assembly must be a little off. Seems that the baffles must come loose at the screw and it tends to cause the attachment nubs to wear. The parts were delivered in no time, had the screws to replace the old screws (which was cool) all in all, the install went without a hitch. Plus, the site is great, easy to identify parts and the order process is a piece of cake. Maybe your folks could come over and redesign our parts site!

I removed the screws holding the fragment of the door, removed the door fragment then placed the screws in my new replacement door (that got here in record time - THANKS!), put it in place, fastened the 2 screws and the problem was solved!!! I am NOT a diyer so this was great for me!!!

First I waited 6 days after i was E-mailed the part was shipped until it was shipped, then waited two more days to get the part!
Then i removed two TORX screws removed old handle then installed the new one in reverse order.

Removed hot/cold water hoses from back of washer at water inlet valve. Pulled off top of washer by removing 3 screws at back of panel. Noted that water inlet valve had been damaged in move from storage. Pulled off 4 wires, 2 for hot and 2 for cold. Removed 1 screw holding inlet valve assembly to frame. Used pliers to release retainer ring on hose. Removed hose from valve outlet. Reversed process to install new valve.

I unscrewed thebolts from the old handle using a small flat screwdriver and removed the cracked handle. I then tossed away all the old duct tape holding the old handle together. Replaced new handle using same old bolts.Strongly cautioned children and husband to not wrench the washer handle open and closed. Tah Dah! Done.

I removed two screws and removed broken piece and replaced the handle with the same two screws. The color and match of the handle was perfect.

Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Removed 2 torx head screws and replaced handle

easy process: troubleshoot problem on website-- order part--get part--watch "how to replace"video on you tube-- get it done with only a screwdriver--go out for movie and dinner with $$ saved.

When I looked at the website for latch repair they showed a video (can't remember which brand but not Amana) where you had to take off the top and front of the washer to get at the latch part on the washer. For the Amana I had, you simply had to pull out a portion of the rubber gasket held onto the washer by a wire/spring combination (you can take the wire off) to get at the latch assembly. You could then undo the three screws holding the latch to the washer, pull it out and unplug the three wiring connections to remove the old latch. Then plug connections into the new latch, reinstall, tighten screws and fit gasket and wire/spring assembly back together. Much easier than going thru the top and front of the washer!

Removed covers per instruction video provided by website

Turned off power, turned off water supply, removed water supply hoses, removed top of washer, photographed electrical connections, removed intake hose, removed screw from part to the machine and removed valve and replaced. Reverse order to install new part and test water supply.

Follow the video when you find the part. It's spot on, exactly what you see and can expect.

Easiest repair on 2003 front loading washer. This unit cleverly uses star tool machine screws with a hex head so you can pick your favorite tool. Turn off the water supply. Remove the hot and cold hoses at the inlet valve, draining any water into a small bucket. Have a towel for dribbles. *This is a good time to examine the hoses and replace them if they are anything other than perfect. Burst or leaking hoses is the #1 cause of water damage in homes.* Three screws releases the top cover which slides 1/2 inch back and lifts off easily. Remove one screw securing the inlet valve (same size screw as the others). Pull the old inlet valve away from the rear panel for easier access. Remove the 4 wires from the solenoids (they pull straight off but maybe need a little finesse), and re-attach to the new inlet valve. Using pliers, release the hose clamp on the old valve sliding it down a couple of inches, then move the hose to the new valve and reposition the hose clamp. Toss the old inlet valve in the trash, screw the new one in place, replace the top panel, reattach and hand-tighten your hoses, turn on the water, look for any leaks, and go have a three martini lunch with the money and time you saved.

First took a picture and printed after disconnecting machine electric supply and removing top cover. removed screw holding vale in place, removed wiring .removed valve,attached wires to new valve inserted in place attached tubing and installed mounting screw and hoses, checked all again and tested