Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GHW9200LW0 > Instructions

GHW9200LW0 Whirlpool Washer - Instructions

All installation instructions for GHW9200LW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9200LW0
106-120 of 295
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Little boy banged too hard on the door, broke it!

  • Customer: Dung from Brooklyn Park, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 36 people found this instruction helpful
Went to PartSelect, looked up the model number and there it was. Part arrive within expected timeline and installation took less than five minutes.

Drain Motor

  • Customer: Dana from Concord, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 2 of 3 people found this instruction helpful
Exact fit VERY GOOD Quality would order any part
again

Broken handle

  • Customer: Theodore from Middletown, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Simple. Found my torx bits, removed the screws, removed the old handle, placed the new handle in position, replaced screws.

This happened because I failed to wait for the click on the machine before I opened the door. It's a front loader and it needs time to drain the water before you open the door.

Bent slide on pedestal

  • Customer: Donald from Greenfield, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 6 people found this instruction helpful
Note that the problem was with the pedestal, not the washing machine. In the process of attaching the two units together, the drawer in the pedestal is removed. When I tipped the assembly up, the slide slid out and locked horns with an object, bending the slide. The slide is an easy replacement. Just one screw holds it in place. A slot in the slide mates with a tab to hold the back side of the slide in place.

drum continuing to fill with water

  • Customer: Steven from Fort Salonga,NY 11768, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 2 of 3 people found this instruction helpful
Replaced inlet valve. Took top cover off. Accessed inlet valve. Removed hoses. Replaced valve. Works like a charm.Corrected problem

Baffle broke off

  • Customer: Robert from Ellison Bay, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
The baffles do push thru slots in the drum and by then pulling them towards you, it moves slightly locking them into place. There are screws supplied and they could be installed to aid in the baffles not coming off as ofter but this cannot by done by the average person for you would need special tools and allot of fixet smarts and patience. My washer can be set at a higher spinout speed and this does save on drying costs but the trade off is the baffles break off way too often. There are metal tabs in the drum that are raised up and snap behind tabs on the underside of the baffles as you slid them towards you install them. If you rebend these tabs up with a longnose pliers twice as high as they are, they will have more holding force, keeping the baffles from coming off as often. In my opinion, the baffles should have been designed to slide backwards to lock them in place, not foward. If you look at how they are shaped, they natually have pressure pushing them towards the back of the drum in the spin cycle which just contributes to the problem of them coming off in the first place.

water backup when not in use, strip threads

  • Customer: Gary from Kenosha, WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Replaced handle on frontload

  • Customer: Patrick from Platte City, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed 2 torx head screws and replaced handle

water inlet valve leak and hose

  • Customer: Paul from Big Torch Key, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

broken door handle

  • Customer: Morgan from Marysville, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Took two screws out, removed broken handle, replaced with new handle and put two screws back in. Ridiculously easy. :)

door handle cracked from top bolt almost all the way through

  • Customer: CHERYL from CASCADE, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I unscrewed thebolts from the old handle using a small flat screwdriver and removed the cracked handle. I then tossed away all the old duct tape holding the old handle together. Replaced new handle using same old bolts.Strongly cautioned children and husband to not wrench the washer handle open and closed. Tah Dah! Done.

The door handle cracked

  • Customer: Paul from Lexington, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
First I waited 6 days after i was E-mailed the part was shipped until it was shipped, then waited two more days to get the part!
Then i removed two TORX screws removed old handle then installed the new one in reverse order.

one of the baffles came off

  • Customer: Tim from Kent, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
The design of the baffle assembly must be a little off. Seems that the baffles must come loose at the screw and it tends to cause the attachment nubs to wear. The parts were delivered in no time, had the screws to replace the old screws (which was cool) all in all, the install went without a hitch. Plus, the site is great, easy to identify parts and the order process is a piece of cake. Maybe your folks could come over and redesign our parts site!

Dryer door handle had broken off

  • Customer: Lisa from Dothan, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the screws holding the fragment of the door, removed the door fragment then placed the screws in my new replacement door (that got here in record time - THANKS!), put it in place, fastened the 2 screws and the problem was solved!!! I am NOT a diyer so this was great for me!!!

Water Intlet Valve Stuck Open

  • Customer: MICHAEL from VALE, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Shut water off to washer, unhook hoses, removed back panel of washer, removed screw that holds the valve in place then unhooked the water line that connects to the washer and removed part. Place new inlet valve in position and hooked hoses and mounted it in place, put back panel back on and hooked hoses up and turned water on. Did a test wash and it worked
All Instructions for the GHW9200LW0
106-120 of 295