Models > GHW9200LW0 > Instructions

GHW9200LW0 Whirlpool Washer - Instructions

All installation instructions for GHW9200LW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9200LW0
31-45 of 292
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellow was ripped at the fold, leaking water into the casing.

  • Customer: david from Goose Creek SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
Removed the top panel. Removed the control panel (one screw behind the detergent drawer). Removed the three screws that held the door latch and switch (pushed it through). Removed the spring-loaded wire that fastens the boot to the door panel(look very closely around the bellow around the opening for the door). Removed the four screws at each corner of the front panel and removed the panel (door still intact). Loosened the band clamp that holds the bellow to the tub. Removed the vent tube from the old bellow and installed on the new bellow. Installation is the reverse of the removal. One tip: when installing the spring-loaded wire around the door panel opening, use several small (padded end) spring clamps to hold the wire in place as you install the wire. If you do not, the areas that you have installed will come undone. Be sure to be careful and use padded ends so that you lessen the likelihood of puching a hole in the new bellow.

Rubber Gasket (bellow) door seal "worn" out

  • Customer: Dan from Hudson WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 25 people found this instruction helpful
Have to remove the front two sections of the washer and top- I had to remove the control panel too. POS kenmore gasket failed after about 2.5-3 years. Old gasket got holes in it - If you have a HE3 or HE4 model- look for it! you will get them too!!! Guaranteed.

shaking washer

  • Customer: Dean from Morrisville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 17 of 31 people found this instruction helpful
twisted old shock absorbers out and snapped new one inplace...did not really fix my problem though

Two problems- Error code FH, Water filling drum when washer off

  • Customer: William from Longwood FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 11 people found this instruction helpful
The Part Select website has some great information provided by customers. I search my error code problem that shut down the washer when filling and found the most likely scenario was a faulty flowmeter.
The other problem happening at the same time was the drum filling with water when the appliance was not in use. I thought the two problems were related, but upon further research decided that the most likely cause was a faulty water inlet valve.
I order the parts from Part Select and I could not believe how fast the shipping was. I just ordered regular ground but the parts got here in a couple of days.
The repair was easy. Remove four screws (need a star bit) from the top lid of the washer and remove the cover. The flowmeter and the water inlet valve sit right on top of the washer. Even with the lousy set of pliers I used, removing the clamps and disconnecting the hoses on both parts was easy off and easy back on. I had more trouble with the electrical leads on the water inlet, only because they were on so securely and I didn't want to rip out the wiring.
All together the repair for both parts took about 30 minutes.
Make sure you turn off the water supply and be ready to mop up a little excess water from the water supply lines when you disconnect them from the washer's water inlet valve.

Drum didn't turn/spin

  • Customer: john from chester NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 14 of 24 people found this instruction helpful
1) Removed back of washer
2) Removed nut holding pulley
3) Pulled pulley off shaft
4) Put new pulley on shaft
5) Replaced and tightened nut
6) Replaced belt on pulley
7) Replaced back panel
7) Washed pile of laundry

would not spin of agitate

  • Customer: Doug from Hartselle AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 12 of 18 people found this instruction helpful
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Door would not lock

  • Customer: Tina from petersburg VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.

Water leak through bellow next to the washer door

  • Customer: Jacek from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
simple removal of few screws holding the washer panels and replacing bellow. 20 minutes to complete entire job. Kenmore mechanical washer design is very simple so all components access is very easy.

door lock was broken

  • Customer: Johnny from Homestead FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 25 people found this instruction helpful
door hook strike was broken half broke in the door the other half stayed in the lock i removed the one pcs from washer with pliers and on the door with a star wrench

FH code-4 minutes into cycle

  • Customer: robert from LITLE RIVER SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 9 of 10 people found this instruction helpful
remove 3 screws of top panel at rear. slide top to rear 1/2 inch and lift up. disconnect wire to flometer, remove clamps on hoses and remove, reverse to install. did not fix problem. ck'd screens at fill valves. ordered new fill valves--problem solved. solenoids must not have been opening up all the way.

Motor Control Board faulted.

  • Customer: Brent from Normandy Park WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 14 people found this instruction helpful
I read the instructions once and then started. It was easy but did take an hour to do the entire job.

Broken lock needed replacement

  • Customer: Alexander from Miami FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 10 of 14 people found this instruction helpful
The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old lock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.

Washer filling up with water when not in use

  • Customer: Dominick from Parker CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 8 people found this instruction helpful
Very simple repair:
- Turn off water and detach water supply hoses. (Good to have a bucket nearby to catch water left in hoses.)
- Remove 3 screws from the back of the lid; slide lid back 1" and lift off.
- Valve is mounted just under the lid on the back wall of the washer -- remove 1 screw from back of washer that holds valve assembly in place.
- Remove the 4 electrical connectors (2 black & 2 white) I numbered them with a sharpie so I wouldn't forget how to reattach them. :-)
- Use pliers to squeeze & slide the little hose clamp that holds the internal hose on the valve assembly. Once the clamp is out of the way, pull the hose off the valve assembly.
- Reverse the process to install the new valve assembly.

I ran into a little problem mounting the new valve assembly. The screw hole in the back of the washer did not line up with the mounting hole in the valve assembly. I had to drill a 3/16" hole just to the right of the original screw hole on the back of the washer. Used the new hole to mount the valve assembly, done.

Worn out hose had a hole it it.

  • Customer: Edward from Clinton MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 10 of 15 people found this instruction helpful
I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.
All Instructions for the GHW9200LW0
31-45 of 292