GHW9200LW0 Whirlpool Washer - Instructions

Removed the two screws from the old handle and screwed on the new handle.

I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

Husband out of town, house full of company (all women) and the dryer breaks. Yikes! Your company got the part to me so very quickly, I replaced the knob in minutes and all the women got to do their laundry. Happy happy group. Thanks!!!!

First and foremost, the screws are not Phillips Head. They are a star shaped screw head. Removed screws, put new handle on washer, screwed it snug and done. More time spent getting correct screwdriver than repairing the handle.

Removed the top of the washer by removing 3 screws on the back and sliding the top back and up. Removed the power cord and pipes. Next removed a screw holding the valve in place. Labeled the wires and pulled them off. The hard part was moving the locking tube ring further back on the tube before pulling the inlet tube off the valve. Reattach the black inlet tube and locking ring. I had to keep working it before it was in the right place. Some have mentioned that the hole didn't line up when they installed the valve. It turns out that there is a small slot in the plastic threaded tubes. One needs to wiggle the valve until the sheet metal rear wall fits in. Then the valve can be slid into position. Attach the mounting screw, hoses, top, power cord and try it out.

it was very easy. the shelf snapped right into place and the light went right in. also, the handle on my Whirlpool washer was broken and a replaced it with a screwdiver. the parts came within two days. Excellent service. Thanks

Baffle just snapped into place. . . . . So easy!

I unscrewed the three small sheet-metal screws holding the washer top to the frame and slid the top aft and laid it on the floor. Then I took fine sandpaper and cleaned the plug contacts from the various components connected to the main control board. After five years or so I have found that most copper connectors will corrode and prevent electricity from flowing properly. That did not correct the problem. I checked the flow control device and it appeared clear and not binding. Then I pulled the drain pump filter and it was clear. I could hear the water pump running and the water flowing out the normal rubber hose. But the washer would stop three or four times during a wash cycle. Pressing 'RESET" and "START" would start the washer again. At the end of the cycle my wife noticed there was water in the washer tub. It had to come in via the water control valve. This is the valve you screw the hot and cold water hose into. It is a ice blue color and held in by one screw. I unscrewed the two hoses and removed the one screw. Then I had to slip the black supply hose from the valve leading to the flow meter. I disconnected the four electrical connectors and installed the new valve and found the screw hole did not align with the screw hole in the washer frame. I used a eighth-inch metal drill and drilled a new hole which lengthened the slot that the mounting screw normally went through. After I re-connected the hot and cold water lines to the valve I turned the water back on and put the top back on the washer. The washer worked like new. No stops. I did notice before changing the valve the water would flow into the washer tub like beer coming from a tap. After installing the new valve the water flowed in at three times the rate like a garden hose.

Remove the 2 screws, broken pieces. Put new handle in place with the screws, all done!

easy fix

I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

Replaced water valve new valve had different electrical connections so I had to replace the connectors job took about 20 minutes. Washer is now operating correct

shut off water valves, took out 3 torx screws that hold the top on, slid then top back just a bit and removed, took the hoses off, took the screw out that holds the water valve and lifted the valve up to remove the wires and hose. Put the wires and hose on the new valve and re-installed, connected the hoses and checked for leaks, put the top on called it a day.

Take the spring hoop on the front of the bellow. Take the dinner bellow ring off. And reverse process

Removed the two screws, removed the cracked handle, replaced with the new handle, put the two screws back in. 2 min. repair and I didn't even ask my husband for help. Simple!!!!