Models > GHW9200LW0 > Instructions

GHW9200LW0 Whirlpool Washer - Instructions

All installation instructions for GHW9200LW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9200LW0
16-30 of 286
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Washer became unbalanced and broke the latch on door

  • Customer: Glenn from Las Vegaas NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 26 of 32 people found this instruction helpful
Had to take the entire front of the washer off to replace the door latch.

F/H error code.

  • Customer: Jeff from Naples FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 23 of 28 people found this instruction helpful
Removed the top (3-4 screws at back). Flowmeter has 2 hoses with hose clamps. Removed with plyers. Simple electrical connector removed.

Reversed procedure. Running perfect now.

How did I know it was the flow-meter? Read the service manual as possible causes to narrow it down. Disassembled old flowmeter and cleaned. That fixed for awhile. Problem came back, could 'tap' on flowmeter to temporarily fix. This convinced me that was indeed the problem.

The flowmeter is just a simple vane that moves as water flows across it, and sends pulses each time it rotates. If it 'sticks' then the computer doesn't think any water is coming in - hence the error. Tapping on it would 'unstick' long enough to confirm problem.

The door handle was broken

  • Customer: VIVIANA from DORAL FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 23 people found this instruction helpful
First i remove the 2 screws that hold the door handle and take out the broken piece, put the new one and then put the screws on their place. It couldn't be EASIER!!!!!

Also I want to tell you that Im form Costa Rica and the best thing is that I order this on Sunday at 3pm and I receive this part on Thursday, FASTEST SHIPPING EVER!!!

THANKS FOR EVERYTHING, I HOPE THAT WE CAN DO MORE BUSINESS AGAIN!!! HIGHLY RECOMMENDED!!!

Bellow torn on HE3t Kenmore

  • Customer: Bruce from Tucson AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 24 of 35 people found this instruction helpful
Take off 3 screws at back of top panel and remove. Remove screw to the left of the soap dispenser and push tab on the right inside the machine to remove control panel and lay the panel on top of the machine without disconnecting. Remove 3 screws on the bottom to remove the bottom panel. You have to pull a bit hard to get it off. Remove 3 screws to push through the door lattch and safety switch. Push the window washer nozzle head through the bellow along with the soap feed nozzle.Remove the retainer wire/spring from the bellow where it attaches to the middle panel/inlet. Remove two screws at the top of the middle panel and two screws on the bottom to remove the middle panel with door attached. Loosen the retainer strap ( a large hose clamp) which anchors the bellow to the tub. Remove the plastic nozzle from the window wash hose and mount it in the new bellow. I couldn't get the plastic retainer washer off the nozzle but managed to seat the bello between the washer and the nozzle anyway. Connect the hoze to the nozzle making sure it's pointed in the correct direction. Pull the oblong soap dispenser nozzle into the corresponding bello opening. Seat the bellow around the internal tub opening and place the large hose type clamp, after unthreading it, around the bellow and tighten. Install the middle panel and attach the door latch and safety switch. Now seat the front part of the bellow to the middle panel and attach the retainer hoop/spring. This is a little tricky. I moistened the front rim of the bellow so the hoop would slide over the edge better. You have to stretch the spring to get it to seat properly. Having experience changing bicycle tires helps. Then install the control panel and other panels.

One of the Baffle's had broken free from the drum.

  • Customer: Loren from Brownsboro AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 19 of 21 people found this instruction helpful
While looking at the new baffle it became evedent that I would need to remove the top of the unit to secure the new baffle to the drum. This was easly done by removing the top of the unit. I removed the three screws from the top back of the unit. Once the top was off I located the inlet tube for the detergent to the drum. I was able to spin the drum and locate the underside of the baffle by looking through the hole where the tube had been attached . I then installed the baffle and snapped it in place. I turned the drum to locate the hole again and installed the screw that was supplied with the new baffle. I then returned the tube back to the location it had orginally been installed. I returned the top and reinstalled the screws to the back of the unit. Whrilpool wanted to replace the entire drum at a cost of $480.00 for the part alone. This is much more cost effective with just a small bit of work. I have contacted Whrilpool for the part number and they would only tell me that I needed a whole drum. I was contacted by a rep from Whrilpool and she told me that I was wrong I could not have done this without replacing the whole drum. My wife will tell all who ask that this unit is working wonderfully.

Washer leaking

  • Customer: Alexander from Miami FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 18 of 21 people found this instruction helpful
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.

Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.

The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machine requires brute force.

Once the hose was out I found some bra under wires which is what probably punctured the hose.

Removed the front filter and found a bunch of nails.

Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.

Water would not drain, motor died

  • Customer: Michael from Worcester MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 16 of 20 people found this instruction helpful
Remove the lower front cover there are three small torx type screw. The pump is the very first thing you see. Have a wet and dry Vac available you will need it. The drain pump and the drain lines contain a lot of water. Unscrew the big white drain plug at the pump and clean up the water, remove the front small mounting screw and disconnect the two hoses in the back of the pump with pliers and follow the pre-printed steps in reverse. If your machine is more than six years old you will have to use a utility knife and remove a piece of plastic on the electrical connector that is from the washer wiring, if you force the connection on it will brake, look at the connection and the plug and attempt to plug it in before you install the pump. It is easy just be-aware of the connector.

Movers wouldn't accept washer w/o shipping bolts

  • Customer: Rob from Yakyma WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 15 of 17 people found this instruction helpful
Like most folks, my daughter has tossed the shipping bolts after her puechase, I moved her the first time w/o any thought to it but commercial movers won't do that, they will chg. you to have it done and it's not cheap, akin to an appliance repair. This kit contains all four bolts/spacers, (2) upper and (2) lower. Hard to tell from the decription but a sweet gal on the help desk assured me of it. Got it fast and got them installed in minutes, easy to do and wrote a big note on the back of the washer to save them!! No idea why your owners book says "do not reuse".

Plastic Knob Cracked off machine

  • Customer: Susan from Glen Ellyn IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 17 people found this instruction helpful
It was super easy...as the knob (Part No. 18 on our Whirlpool Duet Dryer) broke off cleanly leaving the metal pin exposed....(we had been turning it with pilers in the interim) so I just popped the new knob on and we were good to go! It was really easy to do and easy to locate the necessary part on your site. I won't hesitate to use your company and website again. Thank you for making all the parts available and saving us a service call!

error F 11. Mashine would not run

  • Customer: Christina from Englewood FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 15 of 22 people found this instruction helpful
removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.

Noisey when drum turned

  • Customer: James from North Pole AK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 14 of 19 people found this instruction helpful
To verify it was the motor making the noise not the drum bearing I removed the belt and rotated both by hand to see which one made naoise - then I ordered the motor.
To install the motor remove rear panel, slip belt off, remove 1 bolt holding motor in, carefully slide motor towards you until pivits disengage. Wires are ling enough to set motor on bottom of washer and rotate for easier access to connector. Install motor in reverse sequence.

Standing water in drum while not in operation. Bad solenoid on water inlet not staying closed.

  • Customer: Jay from Asheboro NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 13 people found this instruction helpful
Turn off both hot an cold water supply valves. Unscrew both hot and cold supply hoses from rear of washer making note of which inlet they came off of. Pull washer out to access screws to remove top cover and water inlet valve. Remove top cover unscrewing 3 torx screws on the rear of the washer. Unplug the 4 wires wires from water inlet valve - make sure you remember which pairs go to which solenoid. Remove 1 phillips head screw that secures the water inlet valve to the back of the washer. Remove water inlet valve. With a pair of pliers loosen the hose clamp and remove the hose from the inlet valve. Take the new water inlet valve and loosen hose clamp with pliers and push the hose onto the barbed fitting as far as it will go. Make sure hose clamp is over barbed fitting securing the hose. Attach both pairs of wires to the solenoids in the same position that you removed them. Position water inlet valve into place and secure with phillips screw. The part that I received did not quite line up with the hole on the rear of my washer so I had to elongate the existing hole on the rear of the washer with a drill so I could secure the water inlet valve as designed. Screw on both water supply lines making sure the hot and cold are screwed back on to the right inlets. Turn both water supply valves on and test looking for leaks. Secure the top cover back on with the 3 torx screws and push washer back into place. Viola! Ready for the next load of wash.

Bellow was ripped at the fold, leaking water into the casing.

  • Customer: david from Goose Creek SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 14 people found this instruction helpful
Removed the top panel. Removed the control panel (one screw behind the detergent drawer). Removed the three screws that held the door latch and switch (pushed it through). Removed the spring-loaded wire that fastens the boot to the door panel(look very closely around the bellow around the opening for the door). Removed the four screws at each corner of the front panel and removed the panel (door still intact). Loosened the band clamp that holds the bellow to the tub. Removed the vent tube from the old bellow and installed on the new bellow. Installation is the reverse of the removal. One tip: when installing the spring-loaded wire around the door panel opening, use several small (padded end) spring clamps to hold the wire in place as you install the wire. If you do not, the areas that you have installed will come undone. Be sure to be careful and use padded ends so that you lessen the likelihood of puching a hole in the new bellow.

Rubber Gasket (bellow) door seal "worn" out

  • Customer: Dan from Hudson WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 15 of 25 people found this instruction helpful
Have to remove the front two sections of the washer and top- I had to remove the control panel too. POS kenmore gasket failed after about 2.5-3 years. Old gasket got holes in it - If you have a HE3 or HE4 model- look for it! you will get them too!!! Guaranteed.

not pumping out the water

  • Customer: Dale from Ridgely MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 14 of 22 people found this instruction helpful
Disconnected 2 hoses and 1 screw and remove3d the old pump and reversed the proceedure to install the new pump.A piece of cake. Thanks
All Instructions for the GHW9200LW0
16-30 of 286