Models > GHW9200LW0 > Instructions

GHW9200LW0 Whirlpool Washer - Instructions

All installation instructions for GHW9200LW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9200LW0
226-240 of 286
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No problem

  • Customer: Patty from Ironton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
2nd screwdriver I tried worked fine. unscrewed the broke one and replaced the new one. very simple. We take good care of our house items and i,m so glad when you can get parts years later.

door hinge worn out , door handle broken

  • Customer: Bernardino from Bronx. NY NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
remove old worn parts , there was a little difficulty removing one screw due to rust but otherwise it went well.

door handle broke in half

  • Customer: Lisa from Duluth MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Gave handle to husband who installed it in less than 15 minutes. Your service was great!

Broken door handle

  • Customer: Theresa from Roselle IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy to replace, color doesn't match but it works great

Door Lock Latch Broken Inside

  • Customer: Chris from North Reading MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy repair, once I read the reviews and watched a couple of you tube videos. I just released the band holding the gasket in place, pulled it back, unscrewed the latch and installed a new one. Less than a 10 min job. I am glad I found this web site, thanks guys!!

The two attachement supports for door handle completely broke off.

  • Customer: Samuel from Fresno CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the brokern door handle attachment support screws off with my power drill in less than 10 seconds and intalled new handle in 20 seconds using the same power tool. Washer was ready to go.

The washing machine wouldn't drain

  • Customer: Ann from Algonquin IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!

Broken latch on front of washer

  • Customer: Brenda from Citrus Heights CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.

Door handle cracked

  • Customer: Nancy from Beaverton OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed the old handle and screwed the new one on. It took about 45 seconds!!

Door handle was cracked and had to be replaced

  • Customer: Kevin from Beaver PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The part was the right one, so it consisted of 2 screws out and two screws in. 3 minutes total. I needed to use an Allen wrench instead of a screwdriver, as was advertised.

Door handle broke off in two.

  • Customer: Melissa from Searcy AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed old pieces and used these screws to attach new handle. Easy!

Old hinge was worn and sagging.

  • Customer: Jason from East Quogue NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easily took the old door off of the dryer unit then removed the hinge bracket and replaced it with the new part.

Inlet valve replacement

  • Customer: Zane from Cheyenne WY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Used nut driver to remove 3 screws from rear of washer and remove washer top. Used Torx driver to remove single screw holding valve assembly in place. Loosened hose clamp with adjustable pliers and then unplugged 6 electrical plugs. Reversed process to put everything back together. Very simple.

handel broke

  • Customer: Karen from Redwood City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
nothing more than a couple of screws. I was impressed with how quickly the repair part arrived. It was only a couple of days. Very fast!

Tub filling with water between washes

  • Customer: Robert from Parkville MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
1. Unplugged washer. 2. Turned off water supply valves. 3. Disconnected water supply hoses from back of washer. 4. Removed three (3) screws that secure top of washer from top/back of washer. 5. Removed top of washer. 6. Disconnected water outlet line from old inlet valve assembly by releasing clamp. 7. Labeled and disconnected spade connections from old inlet valve. 8. Removed single (1) screw securing old inlet valve in place and removed valve from washer. 9. Re-assembled using new inlet valve lickety split faster than a five-legged skunk.
All Instructions for the GHW9200LW0
226-240 of 286