Models > GHW9150PW1 > Instructions

GHW9150PW1 Whirlpool Washer - Instructions

All installation instructions for GHW9150PW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9150PW1
46-60 of 291
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer filling up with water when not in use

  • Customer: Dominick from Parker CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Very simple repair:
- Turn off water and detach water supply hoses. (Good to have a bucket nearby to catch water left in hoses.)
- Remove 3 screws from the back of the lid; slide lid back 1" and lift off.
- Valve is mounted just under the lid on the back wall of the washer -- remove 1 screw from back of washer that holds valve assembly in place.
- Remove the 4 electrical connectors (2 black & 2 white) I numbered them with a sharpie so I wouldn't forget how to reattach them. :-)
- Use pliers to squeeze & slide the little hose clamp that holds the internal hose on the valve assembly. Once the clamp is out of the way, pull the hose off the valve assembly.
- Reverse the process to install the new valve assembly.

I ran into a little problem mounting the new valve assembly. The screw hole in the back of the washer did not line up with the mounting hole in the valve assembly. I had to drill a 3/16" hole just to the right of the original screw hole on the back of the washer. Used the new hole to mount the valve assembly, done.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

door lock was broken

  • Customer: Johnny from Homestead FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 21 people found this instruction helpful
door hook strike was broken half broke in the door the other half stayed in the lock i removed the one pcs from washer with pliers and on the door with a star wrench

Washer would not spin ( F-02 comes on)

  • Customer: Steve from Dubuque IA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 7 of 9 people found this instruction helpful
1-Unplug washer
2-Remove the bottom of the front washer cover 3 screws
3-Locate pump and loosen pump drain cover turn to left just a little enough for water to start draining.
4- Suck-up water with wet/ dry vac. Remove 1 screw holding pump.
5- Flip pump electrical cover up and disconnect wiring from pump.
6- Remove 2 hose clamps. The outlet was not to hard to remove, but the intake was not easy to get the pliers on.
7- Install new pump. See instruction to install. I didn't have to remove any ribs to install the connector as in the instruction sheet that came with the new pump. Also I didn't think it was very clear instruction.
8- Last installing the spring clamps. The outlet went okay, but the inlet I never could get on. I could not get the pliers on the clamp. I fooled around at least 20 min. trying to get the clamp on. I went out and bought a 3/4 to 1 3/4 stainless hose clamp with the worm drive design. That is what took so long.You may want to get new hose clamps before starting.
Other wise I did okay.

Motor Control Board faulted.

  • Customer: Brent from Normandy Park WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 12 people found this instruction helpful
I read the instructions once and then started. It was easy but did take an hour to do the entire job.

kept getting sud or f2 codes

  • Customer: carroll from Paxton MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
I had sears at my house twice to fix this problem.they told me it was a penny in the pump then when that didn't work they came back and said i was using to much soap which i wasn't.What they fail to tell you is that the high effiiciency washers use less water so they put a less powerful drain pump in so they get over worked and lose the ability to get the water out so buy a new pump and it will be like it's new again.

Not Draining - Flashing F-02

  • Customer: Andrew from Southampton MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.

Detergent leaking under Dispenser Drawer down front of Washer

  • Customer: Geof from Garner NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 15 of 34 people found this instruction helpful
Secondary problem was bleach being siphoned from dispenser prematurely when drawer slid in. Replaced Drawer, Detergent Container and Bleach Siphon parts. Appears to have been a change in the siphon design when compared to the original factory part. 5 loads completed since replacement of these parts with no premature siphon of bleach or leakage down the front of the washer.

Plastic door handle broke

  • Customer: Luis from Sharon MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
It took more time to find the right screwdriver bit than to do the replacement. Removed the 2 screws holding the handle. Put new handle in place. Put the 2 screws back in. Done.

Washing Machine Filled with Water When Off

  • Customer: James from Naperville IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Turned off the water and unplugged the machine

Took off the top of the washing machine by removing three screws along the back side

Removed the hoses connected to the water inlet valve

Removed the hose coming out of the water inlet valve

Marked the 4 electrical connectors

Used plyers to pull the electrical connectors off. Needed to just pull hard. Won't break them off.

Remove the screw that connects the valve to the back of the appliance.

I confirmed this was the part causing the problem by blowing air through it with my mouth. I could tell that the hot water side was not closing all the way.

To replace the part, just repeat the steps above in reverse.

Door leaked water

  • Customer: Tom from Spirit Lake IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I removed the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps

The knob that controls the wash setting broke

  • Customer: Richard from Tempe AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
It only took a few seconds to slide on the new knob after it arrived by UPS. The part arrived sooner than scheduled. Great service and product.

door latch error code

  • Customer: Gary from Sonoma CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

washer not drain or spin

  • Customer: LAURA from SPARTA KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.

Washer would not operate, water in drum would not drain. Error code indicated a bad pump

  • Customer: Patrick from Beaumont TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately $150.00 bucks in repair service fees.
All Instructions for the GHW9150PW1
46-60 of 291