Models > GHW9150PW1 > Instructions

GHW9150PW1 Whirlpool Washer - Instructions

All installation instructions for GHW9150PW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9150PW1
286-300 of 300
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Kept getting F2 code and washer wouldn't drain

  • Customer: Janet from Sutton WV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took the front panel below tub and above pedestal off washer. Removed pump and found coins in the strainer. Removed them thinking they may be causing the problem. Put everything back together and tried again. Washer still wouldn't drain. Unplugged it and ordered a new pump. Installed pump after removing the plug and draining water from washer. Replaced pump with new one and washer works like new.

Easiest $300 I've ever saved!!!

  • Customer: Rusty from Pascagoula MS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Part was $150 and the going rate to replace the pump by a repair person is $300=$450. This was super easy and took about 15 minutes, including draining the old pump with my wet vac!! I messed around witht he old one trying to clean it, etc for several weeks because I'm cheap and didn't want to spend the $150. SPEND THE MONEY AND DO IT YOURSELF.

F/H error code

  • Customer: Harry from Lodi CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I replaced the flow meter but that want it, so replaced the water inlet valve and that cured what ailed it. The only pain was that the single screw that holds the part to the washer is a torx rather than a nut like the rest of the back screws. Couldn't see it without pulling the washer all the way out. Hose clamp came off with pliers and the electrical connectors were TIGHT but came off with some effort. Replaced everything and error cleared ok.

need a star srew driver to install

  • Customer: amilee from housotn TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The installation requires a star shaped screw driver to remove the existing the screw holding the door handle. The same screws must be saved and used to install the new handle, which does not come with new screws. So, you do not want to strip the screws removing. Plan ahead with the correct screw driver- you can determine what is needed by looking at the screw head and purchasing an appropriate tool. My handy neighbor installed my new handle, but the screws can no longer be removed should I have to replace the handle a second time. The entire time to remove and install took less than five minutes.

Broken door handle

  • Customer: Harold from Temecula CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws and removed the broken handle. Positioned the new handle, replaced the screws. Admired my repair.

The door handle just broke off

  • Customer: Barbara J from Hackettstown NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I used a phillips head screw driver, however the heads of the screws were not phillips head, they were some other kind of head I have never seen.

Broken door handle

  • Customer: Raymond from Lincoln MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed two philips head screws, took off old handle and replaced with new. Fastened with two philips head screws. Took 60 seconds from start to finish.

One drum baffle broke off drum

  • Customer: Patrick from Maxwell IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It took less time to repair than it took to get new baffle out of the packing sleeve. Set it in drum and snapped it in place. Took about 5 seconds.

Washer would not drain at all. Impeller spun on shaft.

  • Customer: Jeffrey from Marshfield WI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it

The door handle on my washer broke off after pulling on it too hard

  • Customer: Jim from Plano TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The handle is set with two screws (that don't come with the replacement handle so make sure to save them when you take the old handle off). They use the 6 point screwdriver but a regular flathead screwdriver will work - a phillips won't. Take the old screws out, put the new handle on and screw it back in using the old screws. EASY

had no problem

  • Customer: Jerome from kinards SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Placed baffle in drum over slots pushed down on it and slid it back to lock it in place. You will hear it click.

Water comes into washer eben when no in use.

  • Customer: William from Austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the online videos and did the install in about 10 minutes. I did not need to drill a new hole for my particular model as others have needed. It was a basic take the old valve unit out and install the new one.

Bellow ripped

  • Customer: noemi from lakewood NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed video clip that I found online

Broken drum baffles fell off and made holes in my clothes

  • Customer: Normalyn from Newark DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy peezy!! Next day delivery, as promised for parts that could not be found anywhere else. I placed the baffles in the washer and clicked them in using both hands one by one. I'm petite and weigh about 110 lbs. The total installation time was less than 2 mins. I was given a $200 quote just for installation but, spent less than $100 and installed myself. Thank you!! I will not wait so long and shop around next time. I'm going straight to partsect.com to save time and money. Although I have to buy new clothes now since my washer put holes in all my clothes. But, the problem is finally solved and I am so grateful.

The door handle was cracked and needed replaced

  • Customer: Sherry from Boca Raton FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I am a 70 year female - went online to order the part - it arrived a day later - it was absolutely a breeze to repair - I unscrewed the old cracked handle in about two minutes and screwed the new one in in about 2 minutes or less. It couldn't have been easier. I was so pleased that I saved time and money and I could do it myself. The cost of the part was much less than I would have paid at Whirlpool and my labor was free. Thank you Parts Select for making the part available.
All Instructions for the GHW9150PW1
286-300 of 300