Models > GHW9150PW1 > Instructions

GHW9150PW1 Whirlpool Washer - Instructions

All installation instructions for GHW9150PW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9150PW1
271-285 of 300
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The latch was broken so that the front door wouldn't close.

  • Customer: Jennifer from Staunton VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

broken control knob on dryer

  • Customer: Diane from Suwanee GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Husband out of town, house full of company (all women) and the dryer breaks. Yikes! Your company got the part to me so very quickly, I replaced the knob in minutes and all the women got to do their laundry. Happy happy group. Thanks!!!!

Water filling drum when unit was off

  • Customer: Dave from Sammamish, WA WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed the top of the washer by removing 3 screws on the back and sliding the top back and up. Removed the power cord and pipes. Next removed a screw holding the valve in place. Labeled the wires and pulled them off. The hard part was moving the locking tube ring further back on the tube before pulling the inlet tube off the valve. Reattach the black inlet tube and locking ring. I had to keep working it before it was in the right place. Some have mentioned that the hole didn't line up when they installed the valve. It turns out that there is a small slot in the plastic threaded tubes. One needs to wiggle the valve until the sheet metal rear wall fits in. Then the valve can be slid into position. Attach the mounting screw, hoses, top, power cord and try it out.

light was out of the ice machine in front and a shelf in the door broke.

  • Customer: Marge from Ortonville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
it was very easy. the shelf snapped right into place and the light went right in. also, the handle on my Whirlpool washer was broken and a replaced it with a screwdiver. the parts came within two days. Excellent service. Thanks

Front bellow moldy

  • Customer: James from Hopewell NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed video, Slowly. Was easier then I expected. Everything fit perfectly.

Broken drum baffle

  • Customer: LISA from SEIAD VALLEY CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Did it myself, found the model # from your website, received the part, it slid right on,yay, no more tears in my sheets!

Washer would stop at different times with code FH

  • Customer: David from West Chester PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the three small sheet-metal screws holding the washer top to the frame and slid the top aft and laid it on the floor. Then I took fine sandpaper and cleaned the plug contacts from the various components connected to the main control board. After five years or so I have found that most copper connectors will corrode and prevent electricity from flowing properly. That did not correct the problem. I checked the flow control device and it appeared clear and not binding. Then I pulled the drain pump filter and it was clear. I could hear the water pump running and the water flowing out the normal rubber hose. But the washer would stop three or four times during a wash cycle. Pressing 'RESET" and "START" would start the washer again. At the end of the cycle my wife noticed there was water in the washer tub. It had to come in via the water control valve. This is the valve you screw the hot and cold water hose into. It is a ice blue color and held in by one screw. I unscrewed the two hoses and removed the one screw. Then I had to slip the black supply hose from the valve leading to the flow meter. I disconnected the four electrical connectors and installed the new valve and found the screw hole did not align with the screw hole in the washer frame. I used a eighth-inch metal drill and drilled a new hole which lengthened the slot that the mounting screw normally went through. After I re-connected the hot and cold water lines to the valve I turned the water back on and put the top back on the washer. The washer worked like new. No stops. I did notice before changing the valve the water would flow into the washer tub like beer coming from a tap. After installing the new valve the water flowed in at three times the rate like a garden hose.

Broken Handle

  • Customer: Irving from Linden NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the 2 screws, broken pieces. Put new handle in place with the screws, all done!

broken part

  • Customer: steven from ellensburg WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
easy fix

The washer would slowley fill with water when idile

  • Customer: James from DeBary FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced water valve new valve had different electrical connections so I had to replace the connectors job took about 20 minutes. Washer is now operating correct

dispenser drawer handle broke

  • Customer: Barbara from Treasure Island FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
it just snap on in 5 seconds, incredible, can't believe it was so easy, the washer is so old I thought I will have problems fitting it in.

washer was filling with water, while it wasn't being used.

  • Customer: Dale from Sterling AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
shut off water valves, took out 3 torx screws that hold the top on, slid then top back just a bit and removed, took the hoses off, took the screw out that holds the water valve and lifted the valve up to remove the wires and hose. Put the wires and hose on the new valve and re-installed, connected the hoses and checked for leaks, put the top on called it a day.

Door handle cracked

  • Customer: Jan from Jesup IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the two screws, removed the cracked handle, replaced with the new handle, put the two screws back in. 2 min. repair and I didn't even ask my husband for help. Simple!!!!

pump wouldnt drain

  • Customer: Edward from Dayton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
removed three screens on lower front panel removed hoses from pump after opening drain/filter to remove water slid pump forward and out unplugged pump wiring harness reverse to install

Handle had cracked and broke off.

  • Customer: Susan from Danville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed what was left of the old handle, was attached with 2 screws. Used the same screws and attached the new handle. Easy as that. Less than 15 minutes.
All Instructions for the GHW9150PW1
271-285 of 300