Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GHW9100LW2 > Instructions

GHW9100LW2 Whirlpool Washer - Instructions

All installation instructions for GHW9100LW2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GHW9100LW2
61-75 of 319
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Clothes came out dripping wet

  • Customer: Louis from Branford, CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.

Front seal leaked

  • Customer: Ramon from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 15 people found this instruction helpful
It was so easy my wife replaced the part.

Tub would not drain even though pump was running

  • Customer: Steve from Cary, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 6 people found this instruction helpful
Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.

Washing Machine Filled with Water When Off

  • Customer: James from Naperville, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 7 people found this instruction helpful
Turned off the water and unplugged the machine

Took off the top of the washing machine by removing three screws along the back side

Removed the hoses connected to the water inlet valve

Removed the hose coming out of the water inlet valve

Marked the 4 electrical connectors

Used plyers to pull the electrical connectors off. Needed to just pull hard. Won't break them off.

Remove the screw that connects the valve to the back of the appliance.

I confirmed this was the part causing the problem by blowing air through it with my mouth. I could tell that the hot water side was not closing all the way.

To replace the part, just repeat the steps above in reverse.

Broken baffle

  • Customer: michael from barrington, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 13 people found this instruction helpful
I wasted 2 years washing clothes in mu Duet before I repaired it in just two minutes. In those 2 years we destroyed numerous articles of clothing because the missing baffle left sharp metal corners that cut holes in to so many of our clothes. The replacement baffle was easy to find on partselect.com as were installation guides. I can't believe how easy it was!

The knob that controls the wash setting broke

  • Customer: Richard from Tempe, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
It only took a few seconds to slide on the new knob after it arrived by UPS. The part arrived sooner than scheduled. Great service and product.

door latch error code

  • Customer: Gary from Sonoma, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 16 people found this instruction helpful
removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

Washer would not operate, water in drum would not drain. Error code indicated a bad pump

  • Customer: Patrick from Beaumont, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately $150.00 bucks in repair service fees.

Old bellow pulled loose and torn

  • Customer: RICHARD from Portland, OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.

F-20 Error Code

  • Customer: GARY from CLARKSVILLE, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 7 of 11 people found this instruction helpful
Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd

Plastic door handle broke

  • Customer: Luis from Sharon, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
It took more time to find the right screwdriver bit than to do the replacement. Removed the 2 screws holding the handle. Put new handle in place. Put the 2 screws back in. Done.

Washer would not drain.

  • Customer: Mike from Virginia Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_

The water didn't drain, so the drum wouldn't spin

  • Customer: Jill from New Rochelle, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

Door would not open.

  • Customer: MIKE from LONGWOOD, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 14 people found this instruction helpful
It takes 2 people to do this repair.The bellow is the hardest part. One person has to hold the bellow in one spot, and the other person has to put it on the rim of the drum all the way around. Sort of like putting a tire on a bicycle. Dont do what I did and pry the door open. If you do that you will have to get a new door lock control at $54.Take off the lower front panel and reach up to the manual releace tab on the right side and pull down. Please make sure that the power is turned off, unplug the washer from the wall for your safety. The door switch itself is easy to replace, 3 screws, 3 plugs. Hope this helps.

The washer was unable to run without door locking

  • Customer: MICHAEL from DERIDDER, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .
All Instructions for the GHW9100LW2
61-75 of 319