GHW9100LW1 Whirlpool Washer - Instructions

I just take out the botton part and fine what part what i need chage and just chage exactly like the old if yoo dot remember all the wires please take pictures and you hava guia to check went you are finished

I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

The dryer is in a walkway from the garage to the kitchen. One of my boys accidentally brushed up against the knob and it broke off.That happened on a Tuesday night around 9pm.I got on line that night and ordered the part and it arrived onThursday. It almost seemed impossible. That's why I am writing this review.

Removed top of washer and replaced flow meter.

The easiest fix ever!! What impressed me the most, was that I ordered it Tuesday morning, and Wednesday morning it was here!! Will use this site again!! Thanks.

first unplug power cord and disconnect hot and cold water hoses then remove 3 torx screws in back that hold lid on, slide lid back an inch and lift off, one at a time transfer the four spade wire connectors to new part, remove one more torx screw to free valve assembly from back , it slides to one side away from the screw, use pliers to release and move hose clamp back on hose, wiggle hose off old valve and with a little saliva to lube it, slide and wiggle hose on new valve, with pliers release and move hose clamp back in position, slide valve back in position and secure with torx screw, place lid on top and slide forward into position and secure with the three torx screws. reconnect hoses and plug back in.

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

Replace old part

Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.

replaced drain pump.Saved 200$

Removed the screws and removed the damaged handle then screwed on the new one

The water inlet vavle was pretty easy to find once I took the top off. The water input hoses connect directly to it and 2 electrical connection per valve. One screw needs to be removed. The only trick is to slide the valve to the left to remove. It is captured by the sheet metal washer housing at the base of the male hose connetion.

Cleaned hinge area including the hole where the cover snaps into.Started door window side underneath the clear plastic first and then snaped into place. Door handle replacement used standard set of allen keys and removed broken handle parts. started door handle screws 2ea in new handle mount holes and tightened screws snugley but not tight enough to break the plastic handle.turned out to be a great repair!

I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

removed top cover,disconnected wires to valve,removed valve and hooked up a washer hose to test valve,one side was leaking,valve would not close.replaced with new valve that I received in 2 days,do not buy after market.