GHDRE527H1WW General Electric Washer - Instructions

First, turn off water faucets. Next remove control panel. water valve is in back, easily accessible, held in by 2 screws. Removed 2 water inlet hoses and one outlet hose held by a spring type hose clamp. Removed 4 wiring connectors from valve. reverse steps to reinstall.

I removed the four screws at the top of the washing machine and pulled the front cover off. I unscrewed the two screws that was holding the valve and disconnected the sockets. Last put on the part and connected two wires and put screws back in and reconnected the hoses and washing machine is working perfectly.

The part came after 2 days..terrrific.. upon receipt, i attached the new one to the back of the washer and screwed. it all took about 5mins. My washer is back in business. I am very happy abouit it.
thank u.

I looked up what others said about the same problem. Took their advice, ordered the pump and it was installed in less than 30 minutes. This is the third time that we have ordered parts and have had excellent service. We usually get the parts the next day or at most two days. Instructions to repair are exactly like the customers say on the website. I tell all my friends and relatives about your site.Thanks PartSelect!

the repair was easy. I will be call you again, thank you.

just popped it on the existing part! Quite simple...a 5 year old could do it if he was strong enough!

I figured out the problem,watched the video instructor and i did it,couln'd be easier guy h

just like the video showed/////only idid not kno the water would escape from one of the hoses when removed///video did not prepare me for this

My washer was full of water after it wouldn't drain as part of the wash cycle. I used a Wet/Dry vacuum to remove the water from the tub. Followed the video provided on this part page. When I pulled the hose from the wash tub to the pump at least a gallon of water that I was in the bottom of the tub and hose rushed into the base of the washer. It was an unexpected mess to clean up a the end of the job. Pump was fairly easy to remove from the washer, but reinstalling the hoses to the pump was slightly more challenging. The hose from the tub to the pump is about an inch too short to make this an easy fit. I had to have my wife hold the hose clamp open with the channel locks while I positioned pump onto the hose. After the hose was installed, the second hose was much easier to install. With the new pump the washer running like a champ!

ordered new one put on works like a new machine your repair website really helped.

It was as simple as removing the front cover of the washer. After unpluging, using pliers, remove the two hoses on the pump and disconect the two power plug ins. Two bolts that mounted the pump to the frame of the washer were removed and the pump comes out. Re-install the same way with the new pump from partselect and it worked great.

turn the water off and remove the hoses from the dual water inlet valve;4 screws from electric panel and the 2 screws were the dual water inlet valve is,also a little hose;so that set.I put everything back on.now is working

So, I did an internet search using Hotpoint washer as my keywords and selected Partselect to find a new Dual Water Inlet valve. I found the part and called the company to place my order and the associate asked me for my model number to be sure it was the right one. It wasn't, only similar, and she located the correct one for me. I ordered it and it arrived quickly. I had it installed in less than 15 minutes and the washer works just fine now.
Excellent service!

took off the front and replaced easily. I tested it and it worked! The trick to remove front panel is use 2 screwdrivers, one on side, one in front even to lid edge.

The repair was an easy fix. Since the washing machine was already away from the wall, all we had to do was push(in a screwing motion) the hose in the back of the washer. It sealed right up and we were doing laundry 15min later.