Models > GHD5035F01WW

GHD5035F01WW General Electric Dishwasher - Overview

Get Parts and Repair Help for GHD5035F01WW

If you know the dishwasher repair part you need, you can browse the list of all parts on the GHD5035F01WW, or you can search by name or part description. You can also find your part by where it is located on the GHD5035F01WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for GHD5035F01WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the GHD5035F01WW [Viewing 3 of 3]

$0.69

RACK SLIDE END CAP

This part attaches to the rails, for the upper rack, to prevent the dishrack from sliding all the way out.

$11.16

Upper Roller and Axle - Kit of 4

$8.77

Lower Front Dishrack Wheel

This wheel is located on the front lower rack. It is sold individually and comes with the attaching axle.

$10.00

Lower Rear Rack Wheel and Axle Kit

This kit contains one wheel and one axle. It is designed for the rear lower dishrack. Sold individually. Order quantity needed.

$7.04

Corner Tub Baffle - Lower Left

The left and right side baffles should be installed/replaced at the same time. Right side baffle is sold separately.

$7.02

Corner Tub Baffle - Lower Right

This baffle fits the lower right hand corner of some dishwashers. It is black and has a matching left hand lower corner baffle. It is recommended that you replace and install both left and right at the same time.

$46.61

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

$10.02

Piston and Nut Assembly

This is used for the check valve.

$53.64

Door Gasket - White

This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.

$9.20

Gasket Insert

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The rollers on the upper rack broke

  • Customer: Carl from Fairfield TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 462 of 463 people found this instruction helpful
There are eight guides that hold the rack rails in place. Use a Phillips screwdriver to remove the top two guides on each side in order to remove the rack from the dishwasher. The plastic axles on the rack and the rollers snap on. Use the hammer and punch to bend the metal clip on one end of the rail. Remove the plastic end piece then slide the rollers ... read more

Wheel broken off bottom rack

  • Customer: Julie from Maumee OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 459 of 459 people found this instruction helpful
Open the tiny plastic package in inserted the wheel onto the "axle". Opened the dishwasher, pulled out the bottom rack and snapped the wheel onto the rack. Done! read more

The rear wheels were missing on the lower rack.

  • Customer: Teresa from Phenix City AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 458 of 460 people found this instruction helpful
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama. read more