GH9177XLB0 Whirlpool Microwave - Instructions

No repair- just replaced glass turntable.
Right part I needed with first try

PartSelect had the turntable I needed at the best price. Ordering was easy, but best of all, the part was delivered next day. I was able to insert the new turntable plate into the microwave and it was good as new.

Opened the box and popped it in. No problem with that.

The part was sent to me the next day! And it was the right part. Awesome!

set the table on the support ring

This is the second replacement tray we have in installed. The first one ( Not From Here ) we had for less than 5 months, we made a bag of popcorn, and about 5 minutes later we heard a crash, not knowing where the noise came from we dismissed it. The next day we opened the microwave a saw the plate had shattered. So we hope that this will not do the same thing.

My unit is a wall mount/cabinet/built-in model. The repair is actually fairly simple once you determine that the actual microwave is just a component of the entire unit, and that it (the microwave) can be easily removed from the unit. I did not figure this out until after I removed the entire unit (disconnect the power supply, lift the entire bulky, heavy unit out of the cramped space in the cabinet, etc). Once I got it out I figured out how easy it is to remove the actual oven - a couple of screws, literally. The unit is a bit bulky, but not particularly heavy and is quite manageable. I did this entire process alone.

I got the oven out, rolled it on it's side and found the plate to access the motor. The plate is located on the bottom/underside of the unit. The plate is nothing more than a section of the underside of the metal housing that has been cut-out as an access point. This "cut-out" is not complete - that is, not completely cut out so as to all the plate to stay in place without the need for screws, etc, until you actually have to use it. I used a pair of dykes to cut the couple of points still connecting this plate, removed the two phillips screws to remove the motor, disconnected the two wires connected, then reversed to complete the repair. You then flip the cut-out plate over/rotate it, and some screw holes line up. Find a couple of small screws, and re-attach the plate to cover the motor.

The actual fix is really easy, again, once you figure out the simple way to remove the oven. I am an idiot, so you will probably find this much easier. I could probably do this repair now, after my experience, in less than 30 minutes (probably less than 15 minutes). I probably save a couple hundred $ by doing it myself so was well worth the time to do it. Good luck.

Read some instructions and easily found the fuse. Replaced it. Still didn't work. Took control panel off to check door switches. Nothing I read mentioned a second fuse. Tested and it to had blown. Ordered another one. Popped them in. Done.

I looked up a YouTube video of someone with a similar over the oven microwave. That helped me get into the area behind the control panel where the door switches are. I checked the springs and the cam rocker? The thing that actually hits the button on the switch when the door closes. They were in good condition so I assumed the door switch was bad. There are two so I just purchased one figuring (hoping) that only one was bad. And lo and behold only one was bad. Bing bam boom. Put it all back together and I'm set. Not too difficult. Took a week of work because it takes like 50 days to ship. My kitchen looked like a hurricane after image because of all the parts scattered everywhere.

I ordered the part according to the Model number, inserted the part very easily, (and I am soooo challenged in that area) and now it turns again. :)

replace one of the four rack supports which was melting

I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

the burn thru was probably because stirrer motor was not turning, Unplug the microwave .freed the motor up bu manually turning. temporary fix. The cover is held up with small push pin clips. Just pry the cover off with a screw driver or other flat tool. Scrape offf the old silicone. There are two covers in the Kit. you just need 1. Remove the old clips for the roof of the microwave, put a bead of silicone on the new cover where the old was and secure the new cover with the push pins into the clips .

I used a Google search to show how to access the area behind the front panel. There was a folded paper copy with a schematic and wiring diagram in that space.Then I used a multi-meter to determine which of the THREE micro-switches was causing the problem. I called your help line and ordered a replacement switch. The switch was delayed in transit so your agent credited me with the cost of shipping.

When the part arrived, it had three terminals instead of two as shown in the on-line picture but that did not cause any difficulty in using it. It took about 20 minutes to remove and replace the old switch.

All seems to be working well now.

Finding which of the THREE switches was the problem was the most difficult part of the repair. All three "clicked" but the defective one did not click as easily. It needed to be depressed more than the door latch can would provide. Old age?

Remove the microwave from its mount above the stove. Remove the sheet metal top/sides piece. Pop the control panel loose to allow access from the front. Remove more screws that will allow the small inverter to be removed and the big inverter housing to be wrangled loose enough to remove the big inverter. Pop the inverter cooling fan from its mount. Disconnect wires and remove screws to remove big inverter. Install new inverter in reverse process.