Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GH7208XRY4

GH7208XRY4 Whirlpool Microwave - Overview

Get Parts and Repair Help for GH7208XRY4

If you know the microwave repair part you need, you can browse the list of all parts on the GH7208XRY4, or you can search by name or part description. You can also find your part by where it is located on the GH7208XRY4 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.63

Charcoal Filter

The charcoal filter, used in microwaves, removes food odors from the air. If your filter is damaged or you notice strong odors coming from your microwave, it is best to replace it....

$11.09

Surface Light Bulb

This surface light bulb is used in ranges and microwaves. It has a high voltage of 12 and 10 watts. This bulb illuminates and directs light at the bottom of the microwave or the inside of it. It also illuminates the top and bottom of an oven. If your bulb breaks, or the light flicks on an off, replacing it will solve your issues. Pro tip: High voltage capacitors in ranges and microwaves can retain lethal electrical change even when unplugged, to ensure your safety a technician should install this part. Refer to the manual provided by the manufacturer for further instructions.

$5.83

Air Filter

Sold individually.

$8.40

Fuse

If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes before starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.

$51.90

Glass Cooking Tray

$17.33

Turntable Driver

Also known as the coupler. This driver is located directly under the glass turntable, and over the motor. This part helps the glass turntable to rotate.

$26.47

Door Switch - 250V

This door switch (Primary and Secondary) keeps the microwave from running when the door is open. NOTE: Two switches required. Sold individually.

$63.66

Door Handle

Handle only.

$6.51

SPACER

Waterproof seal.

$5.63

Screw

This is screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Glass cooking tray broke

  • Customer: Mark from Agua Dulce, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 30 of 45 people found this instruction helpful
There was no "fixing" per say but we still could not use the microwave without the plate. This has to be one of the biggest plates for a microwave. We ordered this through your company and we had it three days later. THREE DAYS! We had expected anywhere from 1-2 weeks. My husband was so impressed he bookmarked your site for future reference. Thank you ... read more

Replaced door handle

  • Customer: Cedric from Katy, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 29 of 44 people found this instruction helpful
I removed the screws along the top, side and bottom of the door, stuck a butter knife between the outer door and inner door assemblies, then simply removed the two screws holding the handle. read more

Fire in microwave melted several parts

  • Customer: duane from san diego, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 34 of 73 people found this instruction helpful
Remove the filters and use a Torx driver to remove two screws holding the motor. The wires on on the motor are held in place by a plastic clamp that must be pried open on one side. That's all it takes to replace the drive motor. Everything else that makes the turntable spin lifts off from inside the microwave. read more