Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GGG390LXQ02

GGG390LXQ02 Whirlpool Range - Overview

Get Parts and Repair Help for GGG390LXQ02

If you know the range repair part you need, you can browse the list of all parts on the GGG390LXQ02, or you can search by name or part description. You can also find your part by where it is located on the GGG390LXQ02 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for GGG390LXQ02 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$40.14

Oven Rack

Sold individually.

$6.49

Levelling Leg

This levelling leg is just under three inches long. It is all black in color and is made entirely of plastic.

$56.42

Bake Igniter

This part ignites to help bake your food.

$2.61

Screw

This screw is sold individually.

$2.63

Screw, 10-16 x 1

This screw is sold individually.

$14.30

Control Knob - Chrome

This knob has a D shape shaft. Sold individually.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$8.37

Touch-Up Paint - White

18ml

$21.68

2 Piece Broiler Pan

The top of this part is now black.

$81.62

Surface Burner Valve - 16K - Left Front & Right Front

Burner valves are attached to the main gas line. When the switch is turned the gas then flows into a tube that mixes with air, creating the appropriate mixture for combustion.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ignitor was bad on upper oven

  • Customer: David from Temple Terrace, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 45 of 50 people found this instruction helpful
First I removed the lower tray and all parts covering the ignitor on the upper oven. 2. Then I removed the screws holding down the ignitor and flame distributor. 3. I then had to pull out the oven from the wall and remove the back panel to expose the wires connecting the ignitor. This required the removal of about six screws but they were fairly easy to ... read more

Burner valve was seized

  • Customer: Steve from Tracy, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 43 of 49 people found this instruction helpful
Lock the oven/stove controls by holding the START button for five seconds. This shuts off gas to the valve. Remove the knobs from the front of the stove using philips screwdriver. Undo the six screws that hold on the front bezel and remove to find the valve. Unscrew the top bracket using philps screwdriver. disconnect the valve using a wrench (I think i... read more

Socket Light had a bad thread

  • Customer: Edmund from Emporium, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 32 of 44 people found this instruction helpful
Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover read more