This genuine OEM door lock is a replacement part specially designed for front-load washing machines. It is a safety mechanism designed to prevent the door from being opened during the wash cycle. When...
This drain pump and filter assembly is a genuine OEM replacement assembly that is designed for washing machines. It is responsible for removing water from the washing machine tub at the end of each wa...
This door gasket, also known as a door boot, is a genuine OEM replacement made for front-load washing machines. It is blue and made of rubber. The gasket helps to seal the area between the washer tub ...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Chrystal
May 26, 2023
My GE washer is stopping 3 minutes into cycles. Have replaced main board and inlet water valve and still ding this. Any recommendations on what else it could be
For model number GFW850SPN0RS
Hello Chrystal, thank you for your query. You may need to replace the door lock, part number PS12749276, to fix the issue. It prevents the washer door from opening during the wash cycle or spin cycle. If this is faulty, the washer may stop mid-cycle. We hope this helps, good luck with this repair!
The washer had a sudden decrease in the amount of water entering during the normal cycle. It was under warranty and looked at and they replaced the front dial board and the board next to it. Water flow is great but the controls keep turning the water valves on and off during the fill cycle but the level never gets above the very bottom of the drum. It used to fill with a lot more water and currently the clothes are not getting clean. The inlet screens, hoses and valves check out clean and clear. What's component is causing the low water level. Thank you for your advice.
For model number GFW850SPN0RS
Hi Dan, thank you for reaching out. Based on our understanding, it seems that there is an issue with the main control board, part number PS17139257. It manages the washer's functions such as filling, washing, draining and spinning. You may need to replace it to fix the issue. We hope that helps!
What are the 2 different size rubber/plastic cylindrical pieces that are white with a rubber stopper on the end 2 longer ones and 2 shorter ones. Are they just for shipping or do they serve a purpose because they won't stay in. Thanks
For model number GFW850SPN0RS
Hello Brian, Thank you for your inquiry. If they also have a metal screw at one end, then they are just the shipping bolts and are only used for shipping the washer. We hope this helps.
The drain pump will not shut off from time to time. We have to unplug and reset the relay. I have read the relay board should be replace if this continues. I just want to make sure I have it correct before I order the board
For model number GFW850SPN0RS
Hi David, thank you for the question. Yes, you will need to replace the main control board, part number PS17139257, to fix the issue. Glad to be of assistance!
Hello Linda, thank you for your question. There is a Dryer Door Lock Reversal Latch Bar PS12749277. Door lock reversal latch bar lets you move the door lock to the opposite side when you reverse the door opening. We are pleased to have been able to help.
Sediment in your water will ruin these water inlet valves over time. It will reduce the amount of water filling the tub & will be very noisy making a squealing sound.
You’ll need a #2 Philips screwdriver & a standard set of pliers.
UNPLUG ELECTRIC SUPPLY FROM WASHER, TURN OFF WATER VALVES, THEN DISCONNECT WATER LIN
... Read moreES & DRAIN HOSE. Pullout the detergent dispenser drawer. Remove 2 self-tapping screws and & 3 sheet metal screws. Slide front control panel to the right and let it rest on the machine. Remove 3 sheet metal screws to release the top lid cover. Pull the lid towards you and lift off. You’ll see water inlet valves in the left rear. Remove Philips head screws securing water inlet valve. Disconnect electrical wires from the water inlet valve solenoids. Using pliers, squeeze hose clamps and slide down small hoses. Pull off or twist the small hoses from the old water inlet valve. Install the small hoses onto the new Walter inlet valve and reconnect electrical harness to water inlet valve solenoids. Mount new water inlet valve, reconnect water supply hoses & turn on water supply. Check for any leaks before going any further. If no leaks, reinstall top lid & front panel. CONTROL PANEL IS DIFFICULT TO LINE UP WHEN SLIDING IT TO THE LEFT TO REINSTALL. LINE UP THE SLOTS FOR THE SCREWS WHEN REINSTALLING THE CONTROL PANEL. Refasten all screws and slide dispenser drawer back into dispenser pocket. Reconnect electrical supply. Washer should operate normally.
Disassemble according to instructions then remove pump...my only issue was I ordered the pump and paid $11.95 for t 2 to 3 days shipping. I didn't get the part until the following Saturday which was like 6 to 7 days...horrible delivery
