Models
>
GFW650SSN1WW
GFW650SSN1WW General Electric Washer - Overview
Sections of the GFW650SSN1WW
[Viewing 10 of 10]Keep searches simple, eg. "belt" or "pump".
DOOR LOCK
PartSelect #: PS12749276
Manufacturer #: WH01X29528
This genuine OEM door lock is a replacement part specially designed for front-load washing machines. It is a safety mechanism designed to prevent the door from being opened during the wash cycle. When...
$50.13
In Stock
DRAIN PUMPS & FILTER
PartSelect #: PS16217203
Manufacturer #: WH11X29539
This drain pump and filter assembly is a genuine OEM replacement assembly that is designed for washing machines. It is responsible for removing water from the washing machine tub at the end of each wa...
$82.81
In Stock
GASKET
PartSelect #: PS12743601
Manufacturer #: WH05X29514
This door gasket, also known as a door boot, is a genuine OEM replacement made for front-load washing machines. It is blue and made of rubber. The gasket helps to seal the area between the washer tub ...
$115.96
In Stock
Questions And Answers for GFW650SSN1WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Alan
May 24, 2023
I need shipping brace/bolt hardware. What should I order?
For model number GFW650SSN1WW
Hi Alan, thank you for reaching out. The parts you are looking for are the long shipping bolt, part number PS12743589, and the short shipping bolt, part number PS12743588. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Johnny
March 24, 2023
Does this front load washer have a pressure switch on it ?
For model number GFW650SSN1WW
Hi Johnny,
Thank you for your question. There are no switches listed for your washer. It is controlled by an electronic control board, part number PS16743398. There is a pressure hose, part number PS16219920, and a pressure chamber, part number PS16219900, listed for your washer. If you would like to place an order for these parts, please call our customer service line and anyone will be happy to assist you. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Related Parts:
John
May 22, 2023
I replaced the door lock and now it does not want to register that it's locked it blinking door would that be the control board that is bad then
For model number GFW650SSN1WW
Hi John, thank you for reaching out. Based on the description that you have provided, we would recommend checking the user interface control board, part number PS16743398, to fix this issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the GFW650SSN1WW
[Viewing 1 of 1]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Squealing Water Valve When Water Is Filling Washer Tub
Sediment in your water will ruin these water inlet valves over time. It will reduce the amount of water filling the tub & will be very noisy making a squealing sound.
You’ll need a #2 Philips screwdriver & a standard set of pliers.
UNPLUG ELECTRIC SUPPLY FROM WASHER, TURN OFF WATER VALVES, THEN DISCONNECT WATER LIN ... Read more ES & DRAIN HOSE. Pullout the detergent dispenser drawer. Remove 2 self-tapping screws and & 3 sheet metal screws. Slide front control panel to the right and let it rest on the machine. Remove 3 sheet metal screws to release the top lid cover. Pull the lid towards you and lift off. You’ll see water inlet valves in the left rear. Remove Philips head screws securing water inlet valve. Disconnect electrical wires from the water inlet valve solenoids. Using pliers, squeeze hose clamps and slide down small hoses. Pull off or twist the small hoses from the old water inlet valve. Install the small hoses onto the new Walter inlet valve and reconnect electrical harness to water inlet valve solenoids. Mount new water inlet valve, reconnect water supply hoses & turn on water supply. Check for any leaks before going any further. If no leaks, reinstall top lid & front panel. CONTROL PANEL IS DIFFICULT TO LINE UP WHEN SLIDING IT TO THE LEFT TO REINSTALL. LINE UP THE SLOTS FOR THE SCREWS WHEN REINSTALLING THE CONTROL PANEL. Refasten all screws and slide dispenser drawer back into dispenser pocket. Reconnect electrical supply. Washer should operate normally.
You’ll need a #2 Philips screwdriver & a standard set of pliers.
UNPLUG ELECTRIC SUPPLY FROM WASHER, TURN OFF WATER VALVES, THEN DISCONNECT WATER LIN ... Read more ES & DRAIN HOSE. Pullout the detergent dispenser drawer. Remove 2 self-tapping screws and & 3 sheet metal screws. Slide front control panel to the right and let it rest on the machine. Remove 3 sheet metal screws to release the top lid cover. Pull the lid towards you and lift off. You’ll see water inlet valves in the left rear. Remove Philips head screws securing water inlet valve. Disconnect electrical wires from the water inlet valve solenoids. Using pliers, squeeze hose clamps and slide down small hoses. Pull off or twist the small hoses from the old water inlet valve. Install the small hoses onto the new Walter inlet valve and reconnect electrical harness to water inlet valve solenoids. Mount new water inlet valve, reconnect water supply hoses & turn on water supply. Check for any leaks before going any further. If no leaks, reinstall top lid & front panel. CONTROL PANEL IS DIFFICULT TO LINE UP WHEN SLIDING IT TO THE LEFT TO REINSTALL. LINE UP THE SLOTS FOR THE SCREWS WHEN REINSTALLING THE CONTROL PANEL. Refasten all screws and slide dispenser drawer back into dispenser pocket. Reconnect electrical supply. Washer should operate normally.
Read less
Parts Used:
-
Patrick from GLEN ALLEN, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No spin, no drain
Disassemble according to instructions then remove pump...my only issue was I ordered the pump and paid $11.95 for t
2 to 3 days shipping. I didn't get the part until the following Saturday which was like 6 to 7 days...horrible delivery
2 to 3 days shipping. I didn't get the part until the following Saturday which was like 6 to 7 days...horrible delivery
Parts Used:
-
Peter from CLAYTON, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!