GFS227/MN02 Caloric Refrigerator - Instructions

Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.

Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.

Followed the video as a guideline. It was not exactly as portrayed. My husband and I, being long time do it yourselfer's, were able to get around the differences. There were screws, instead of tabs as pictured in the video, plus had to remove 4 screws instead of one to loosen the old icemaker. After 2 days the icemaker is pumping out loads of ice.

Researched the common problem with "dryer not turning on", and tested the top three problems. Removed the dryer front casing and door, unbolted front dryer plate. Used a volt meter on two of the temp gauges, which were fine. Removed the upper back plate of the dryer to the wiring for the knobs and buttons. Used the volt meter on the dryer start button, which was also fine. Went back around to the front and removed the door switch. Tested it with the volt meter and bingo. Replaced that part, dryer works like normal.

I followed the instructions from your video. I did this replacement all by myself. I am a 64 year old woman and have never done anything like this before. It could not have been any easier.

Replaced icemaker and used wire harnnes and plastic cover off old one. Real easy!!

The ice maker change out was easy. The problem was the part came with a different filler cup but the one needed was supplied. Changing to the other cup required taking the ice maker apart and installing the other filler cup. Go to the parts list and find the filler cup. Use instructions found there to change to other cup and then install your ice maker.

removed old icemaker and transfer some of the parts to the new icemaker. The only problem was that I had to disasemable the new icemaker to replace the fill tray with the older style (which was included). Once that was done, installation was pretty easy.

I removed the old ice maker as described by the DIY video and had no problem except, I had to remove the ice tray from the motor section so the end cap could be changed. This only required removal of two Phillips screws on the case of the motor assembly, that are used to to secure the tray. Once the tray was off, the ice ejector could be removed and the end cap was free to change. Everything was re-installed in reverse order and unit was mounted. An FYI to anyone with slow ice making, will need to check their freezer temperature. Make sure it's set to get as cold as 5-10 degrees Fahrenheit. After installing new maker, it was not making ice fast enough, only to find my freezer temperature needed to be changed as well. Everything is working as it should now.

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

My husband took the door off and replaced the door closure cam kit with no problem the door opens without a sound.

First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.