Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GEW9200LW0

GEW9200LW0 Whirlpool Dryer - Overview

Get Parts and Repair Help for GEW9200LW0

If you know the dryer repair part you need, you can browse the list of all parts on the GEW9200LW0, or you can search by name or part description. You can also find your part by where it is located on the GEW9200LW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for GEW9200LW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.71

Door Catch Kit

This kit contains two door strikes, and various door catches to service dryer doors that have one or two catches.

$14.90

Idler Pulley with Tri-Ring and Gasket

A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.

$27.79

Lint Filter

This filter collects lint as it passes through the dryer vent.

$33.11

Dryer Repair Kit

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.

$6.59

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

$33.27

High Limit Thermostat and Thermal Fuse Kit

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.

$5.15

Leveling Foot

Sold individually.

$40.08

Dryer Drum Seal with Adhesive

This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.

$7.20

Touch-Up Paint - White

18ml

$22.35

Stacking Kit

This kit comes with 2 adhesive pads, 2 brackets and 4 screws. This is for stacking the appliances vertically - dryer over washer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Catch part had fallen out,/ was missing

  • Customer: Terri from Saint Augustine, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 566 of 582 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source. read more

Burned out heater element

  • Customer: Alan from Brooksville, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 345 of 383 people found this instruction helpful
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing... read more

felt strip came off lint screen

  • Customer: JEFFREY from FALL RIVER, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 152 of 188 people found this instruction helpful
ordered new lint screen, removed old screen, inserted new screen. read more