Models > GDF530PSM0SS > Symptoms > Leaking

Parts That Fix General Electric Dishwasher GDF530PSM0SS Leaking

Leaking is a commonly reported symptom for the GDF530PSM0SS General Electric Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GDF530PSM0SS General Electric Dishwasher that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

1 Gasket
Fixes Symptom 38% of time
Gasket – Part Number: WD08X21894
★★★★★
★★★★★
27 Reviews

Rated by 17 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This part is a replacement gasket for your dishwasher. The gasket creates a seal at the bottom of the dishwasher tub, so water does not leak out while the dishwasher is running. If you notice water leaking out onto the floor, you should inspect the gasket for damages and replace as necessary. The gasket is gray in color and is approximately 22 inches long. It is made of plastic and is sold individually. This is a genuine OEM part sourced directly from the manufacturer.

$ 8.54
  In Stock
PartSelect Number PS11700870
Manufacturer Part Number WD08X21894

Customer Repair Stories

lower door gasket deteriorated/moldy

The dishwasher had been installed before we added 3/4 oak floor, so I could not pull the dishwasher out from under the counter. That will be a major project when the dishwasher dies.
To remove the door, I removed the two 1/4 " screws on the right and left bottom of the door. I used a box wrench since that was the only way to reach them. One had corroded due to a leak. it took some coaxing but finally came loose. The hint about opening the door 27 degrees and propping it open with two Allan wrenches through the hinge holes was very helpful. Then I lifted the door a little and gently pushed toward the counter releasing the door form the hinges. I took the door off to find a leak and found the right corner edge of the inside tub had cracked. Not sure how this happened. I cleaned and sanded the crack area and used J-B Weld to epoxy the crack. Replacing the gasket was easy. Slide out the old, slide in the new. Everything went back together smoothly. If I hadn't needed to repair the tub, the hint about opening the door all the way and sliding it out part way might have worked to change the gasket. Note. Unlike a stove door the dishwasher door is not that heavy.
Read less
  • Stephen from MATTAPOISETT, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Wrench set
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Gasket at the bottom of the door disintegrated.

Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid door back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.
Read less
  • D from LE CENTER, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
39 of 54 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Dishwasher Tub Gasket
Fixes Symptom 30% of time
Dishwasher Tub Gasket – Part Number: WD08X23476
★★★★★
★★★★★
31 Reviews

Rated by 6 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

The tub gasket, also known as the door gasket runs along the perimeter of your dishwasher basin and creates a seal that prevents water from leaking out when the tub is full. If you notice water on the floor after you run your dishwasher, it may be an indication that the gasket is loose or damaged. If your door gasket is damaged, it will need to be replaced. To replace the gasket, simply pull the old gasket out of the groove it rests in, and press the new gasket into place. This part is made of black rubber and is sold individually.

$ 21.59
  In Stock
PartSelect Number PS11774412
Manufacturer Part Number WD08X23476

Customer Repair Stories

tub gasket was damaged

damage to gasket (had a slit in the area of the utensii baskets.
causing lower right corner of gasket to come out. caused leakage to floor from the lower right corner of door...

As I am 77 yrs of age I was leary of diy but thanks to the reps of
"Parts Select" I actually was able to put in the new gasket myself.It did take some time and lots of patience as it had to be seated correctly..I also had to make sure the new gasket was in the groove as it is supposed to be.
Read less
  • Susan from STATEN ISLAND, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Bad tub gasket

Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.
  • Larry from HAMBURG, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 DIVERTER ASSEMBLY KIT
Fixes Symptom 11% of time
DIVERTER ASSEMBLY KIT – Part Number: WD19X25278
★★★★★
★★★★★
16 Reviews

Rated by 3 customers 

  

A Bit Difficult 

More than 2 hours 

Ratings submitted by customers like you who bought this part.   

This diverter valve assembly is sourced from the original manufacturer for use in dishwashers. The assembly controls the flow of water between different parts of the appliance. It directs water to either the upper or lower spray arms during different stages of the wash cycle, ensuring efficient cleaning of dishes throughout the dishwasher. The valve may become damaged or worn down over time due to frequent use and exposure to heat and chemicals. If the assembly is faulty, you will likely notice leaking from under the door and less water reaching the spray arms. It is best to replace the assembly promptly to avoid further damage to the dishwasher.

$ 95.71
  In Stock
PartSelect Number PS12710077
Manufacturer Part Number WD19X25278

Customer Repair Stories

Diverter assembly leaking

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.
  • Lisa from PULASKI, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Strange noise coming from the dishwasher, later a small leak appearing underneath

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!
Read less
  • Donaldo from ALTADENA, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
4 WATER VALVE AND HARNESS SERVICE ASM
Fixes Symptom 10% of time
WATER VALVE AND HARNESS SERVICE ASM – Part Number: WD15X26140
★★★★★
★★★★★
31 Reviews

Rated by 7 customers 

  

Really Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This is a washer inlet valve assembly for your dishwasher. This valve allows water to flow into your dishwasher at the proper rate. If your dishwasher tub is not filling with water or filling when the appliance is not in use, you may need to replace the inlet valve. It measures approximately 3 inches by 4 inches and is made of metal and white plastic.

$ 32.42
  In Stock
PartSelect Number PS12743161
Manufacturer Part Number WD15X26140

Customer Repair Stories

Dishwasher would not start Would run if you added 2 qt. water manually

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.
Read less
  • Mark from FAIRFAX, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

No water

just bolted on the new one and hooked up the hose
  • Jeffrey from BENNINGTON, VT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
5 DOOR VENT SEAL
Fixes Symptom 4% of time
DOOR VENT SEAL – Part Number: WD08X10092
★★★★★
★★★★★
4 Reviews

Rated by 2 customers 

  

A Bit Difficult 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

$ 32.15
  In Stock
PartSelect Number PS8688151
Manufacturer Part Number WD08X10092

Replacing your General Electric Dishwasher DOOR VENT SEAL

Replacing your DOOR VENT SEAL
6 HIGH LOOP DRAIN HOSE
Fixes Symptom 3% of time
HIGH LOOP DRAIN HOSE – Part Number: WD24X29378
★★★★★
★★★★★
4 Reviews

Rated by 1 customer 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

$ 22.71
  In Stock
PartSelect Number PS16618969
Manufacturer Part Number WD24X29378

Customer Repair Stories

I had a hole in the drain line of my dishwasher.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.
Read less
  • Tina from SOUTH WEST CY, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
7 GASKET - SUMP MANIFOLD
Fixes Symptom 2% of time
GASKET - SUMP MANIFOLD – Part Number: WD08X22758
★★★★★
★★★★★
3 Reviews

$ 22.00
  In Stock
PartSelect Number PS11766955
Manufacturer Part Number WD08X22758
8 Circulation Pump
Fixes Symptom 1% of time
Circulation Pump – Part Number: WD26X23258
★★★★★
★★★★★
14 Reviews

Rated by 6 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This part contains the Piranha clamps in kit WD35X10382

$ 125.15
  In Stock
PartSelect Number PS11772000
Manufacturer Part Number WD26X23258

Customer Repair Stories

Dishwasher ran but didn't wash

I got lucky and found the diagnostic test instructions tucked inside the washer under the kick plate. From there I ran the tests on each component until I narrowed it down to the pump. The pump cost me less than local dealers. The install went well. Watched the online videos to make sure I was doing it right. Was actually very easy and saved hundreds over a service call.
Read less
  • Timothy from CASTLE ROCK, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Sprayer arms didn't operate and dishes were not cleaned

We bought this GE dishwasher new. After 9 months, we started noticing the dishes were not cleaning well. Eventually, the machine just filled up with water and drained. The washing arms didn't work. I replaced fill valve, but that didn't solve it. A GE Tech ran a diagnostic and informed us the pump motor was bad. It was off warranty and repairs would be $300. However, he noted it was easy to do on my own. Two pipe clamps. The part from PartsSelect was 40% less than ordering from GE and was a GE part. Replacement took half an hour and that includes getting it wrong once (one connection leaked due to a bad job attaching the pipe clamp). Works like a champ now.
Read less
  • Eric from THORNTON, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
9 DRAIN TUBE Assembly
Fixes Symptom 1% of time
DRAIN TUBE Assembly – Part Number: WD24X10062
★★★★★
★★★★★
2 Reviews

$ 27.99
  In Stock
PartSelect Number PS6011670
Manufacturer Part Number WD24X10062

Replacing your General Electric Dishwasher DRAIN TUBE Assembly

Replacing your DRAIN TUBE Assembly
10 KIT - PIRANHA CLAMPS PS
Fixes Symptom 1% of time
KIT - PIRANHA CLAMPS PS – Part Number: WD35X10382

Rated by 1 customer 

  

Very Difficult 

More than 2 hours 

Ratings submitted by customers like you who bought this part.   

$ 76.40
  In Stock
PartSelect Number PS6011682
Manufacturer Part Number WD35X10382
Back to Top