Models
>
GDF510PGD2BB
GDF510PGD2BB General Electric Dishwasher - Overview
Sections of the GDF510PGD2BB
[Viewing 6 of 6]Manuals & Care Guides for GDF510PGD2BB
Click to downloadInstall
Installation Instructions
(4.13MB)
Install
Installation Instructions
(0.67MB)
Install
Installation Instructions
(0.46MB)
Install
Installation Instructions
(2.83MB)
Install
Installation Instructions
(0.51MB)
Manual
Owner's Manuals
(12.09MB)
Manual
Owner's Manuals
(12.09MB)
Manual
Owner's Manuals
(11.47MB)
Keep searches simple, eg. "belt" or "pump".
LOWER RACK ROLLER
PartSelect #: PS16217024
Manufacturer #: WD12X26146
This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
$13.13
In Stock
Gasket
PartSelect #: PS11700870
Manufacturer #: WD08X21894
This part is a replacement gasket for your dishwasher. The gasket creates a seal at the bottom of the dishwasher tub, so water does not leak out while the dishwasher is running. If you notice water le...
$8.54
In Stock
Door Latch
PartSelect #: PS6447681
Manufacturer #: WD21X10490
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
$44.23
In Stock
Dishwasher Tub Gasket
PartSelect #: PS11774412
Manufacturer #: WD08X23476
The tub gasket, also known as the door gasket runs along the perimeter of your dishwasher basin and creates a seal that prevents water from leaking out when the tub is full. If you notice water on the...
$21.59
In Stock
Flood Switch
PartSelect #: PS8690623
Manufacturer #: WD21X10519
This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if you...
$53.93
In Stock
END CAP
PartSelect #: PS7783360
Manufacturer #: WD12X10426
This is an end cap for a dishwasher rack. This part is about 2.5 inches long, is black, and is made of plastic. You may need to replaced this part if it is broken, or if your dishwasher rack continuou...
$14.28
In Stock
LOWER SPRAY ARM ASSEMBLY
PartSelect #: PS16542476
Manufacturer #: WD22X27724
This lower spray arm assembly in your dishwasher distributes water and detergent during the washing cycle by spinning around and spraying water in different directions. You can usually find it attache...
No Longer Available
HEATING ELEMENT
PartSelect #: PS16729156
Manufacturer #: WD05X30818
The element heating assembly is found at the bottom of the dishwasher tub, and helps to warm the water in the wash cycle, and dry the dishes afterward. If the water does not heat up during the wash cy...
$56.26
In Stock
Countertop Bracket
PartSelect #: PS11700868
Manufacturer #: WD01X21740
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
$7.49
In Stock
Upper Rack Assembly
PartSelect #: PS16618975
Manufacturer #: WD28X30219
This dishrack is for dishwashers. The dishrack holds the dishes in place during the dishwashing cycle. Follow the instructions in the manual when installing this part.
$82.29
In Stock
Screw 8-16 hxw 1/2 Stainless Steel
PartSelect #: PS258461
Manufacturer #: WD02X10067
Sold Individually.
$8.54
In Stock
Single Speed Drain Pump Kit
PartSelect #: PS16219695
Manufacturer #: WD19X25187
This drain pump kit is for dishwashers. The drain pump kit removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. The kit may include multiple parts; refer to your ...
$113.73
In Stock
Questions And Answers for GDF510PGD2BB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Marco
August 17, 2021
My dishwasher does not heat dry. What might be malfunctioning? Are there parts that i can order and replace? It's about 6 years since i've had this dishwasher.
For model number GDF510PGD2BB
Hello Marco, Thank you for contacting us. We have researched the model you have provided and recommend the dishwasher heating element assembly PS12582671 to fix your issue. Hope this helps.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the GDF510PGD2BB
[Viewing 9 of 9]Leaking
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gasket at the bottom of the door disintegrated.
Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid d
... Read more
oor back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.
Read less
Parts Used:
-
D from LE CENTER, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
39 of 53 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water flowing into dishwasher
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve.
... Read more
I extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch.
Read less
Parts Used:
-
Jeff from AUBURNDALE, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
32 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch not functioning
1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. ... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. ... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.
Read less
Parts Used:
-
James from ALBRIGHTSVLLE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
24 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!