Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GCG950T-03

GCG950T-03 General Electric Trash Compactor - Overview

Get Parts and Repair Help for GCG950T-03

If you know the trash compactor repair part you need, you can browse the list of all parts on the GCG950T-03, or you can search by name or part description. You can also find your part by where it is located on the GCG950T-03 by selecting a section below. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the GCG950T-03

[Viewing 4 of 4]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$61.65

Trunnion Nut - Metal

The trunnion nut (also referred to as a power nut) is made of metal and sold individually. This nut is part of your trash compactor assembly. The trunnion nut has spiked edges and ...

$17.00

Single Roller

This is a single roller and it is a part for multiple appliances in your household. You may also know this as a bearing roller or a wheel assembly. It is roughly one inch by one inch in size, and is sold individually. The function of the single roller is to allow rolling movement within your appliance. Once this piece is screwed in place it will allow you to pull or push that section of your appliance freely. This part resembles a screw with a small wheel around the head.

$203.53

Gear Box Kit

This is a gearbox kit for a trash compactor. The outer casing of the part is made of metal and measures 5 inches wide and 7 inches tall. The gearbox is run by the motor, and allows...

$26.66

SPROCKET 50 TOOTH

$4.13

WASHER THRST

$50.28

Drive Chain

Also known as Endless Chain. Sold individually.

$48.98

Bag Caddy

$20.50

Turn Bearing

$14.56

KEY KNOB TYPE

$6.63

NUT SNAP-IN

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Compactor Piston stays down even though the motor is running

  • Customer: Robert from San Deigo, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 14 of 18 people found this instruction helpful
If the drawer is stuck because the piston is in it, you will have to take the back off to lift the piston in order to remove the drawer.

With the drawer out, tip the compactor on its back to easily maneuver the otherwise heavy piston. Working from the front remove the trunnion nut cover (two hex screws) and then the bad trunnion. You may need to m... read more

Plastic trunnion nut was worn out

  • Customer: Joe from Avondale, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 10 of 12 people found this instruction helpful
The problem with this repair arises after you have removed the old trunion nut and you are trying to get the new one to seat into the narrow bracket that surrounds it and keeps it from turning. You can only screw the trunion nut on so far and then it runs into the edges of the bracket. I found that by aligning the new trunion nut at the proper angle and then... read more

The ram would not raise and the motor kept running.

  • Customer: Scott from Colleyville, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I actually pulled the entire motorized unit out of the case, not knowing what the problem was. I found that the old nylon trunnion nut was stripped. I ordered two replacement trunnion nuts in case the replacement stripped out also. (However, the manufacturer has replaced the old nylon nut with a threaded metal unit that should never strip so I goofed when... read more