Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GCG1700L0II

GCG1700L0II General Electric Trash Compactor - Overview

Get Parts and Repair Help for GCG1700L0II

If you know the trash compactor repair part you need, you can browse the list of all parts on the GCG1700L0II, or you can search by name or part description. You can also find your part by where it is located on the GCG1700L0II by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your trash compactor. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$20.43

Foot Pedal - Black

The foot pedal on your trash compactor is located at the bottom of the unit. This part, when compressed, allows the container drawer on the trash compactor to slide in and out. If ...

Order within the next 6 hrs and your part ships today!
$23.85

Compactor Bags - 15 pack

Using trash compactor bags is a practical way to remove your waste. Because compactors use such high pressure to compress the waste, using compactor bags designed to handle the force are a necessity. The bags measure approximately 21 inches (L) x 9 inches (W), are clear in color, and are made from plastic. This pack of 15 trash compactor bags is a genuine OEM replacement part, and will fit most rectangular 21-inch trash compactors.

Order within the next 6 hrs and your part ships today!
$20.53

Directional Switch

This is a top limit directional switch for a trash compactor. The directional switch reverses the motor direction when the trash compactor has reached the top of the drawer. If you...

Order within the next 6 hrs and your part ships today!
$15.86

NUT POWER ASM

This power nut assembly is made to be used in conjunction with your trash compactor. It comes with five pieces that include the two mounting pins, two clips, and the new power nut. This piece is beige, and roughly 3 inches wide, and almost 2 inches long. For this repair, you will need a screwdriver set or a multi-screwdriver, a quarter-inch nut driver bit, and a flat-head bit. You will need to get inside of your trash compactor in order to replace this part. This means uninstalling your appliance from your cabinets.

Order within the next 6 hrs and your part ships today!
$22.37

Drive Gear - White

If your trash compactor is jammed or stuck with the ram in the down position, you may have a faulty or damaged drive gear. The drive gear is located at the bottom of your compactor...

Order within the next 6 hrs and your part ships today!
$14.47

FRAME ROLLER ASM

Order within the next 6 hrs and your part ships today!
$19.78

GEAR MOTOR

Order within the next 6 hrs and your part ships today!
$31.89

Start Switch

Order within the next 6 hrs and your part ships today!
$20.23

DOOR TILT SWITCH

Order within the next 6 hrs and your part ships today!
$268.94

Drive Motor and Gear Kit

This motor operates the trash compactor press that helps compacts the trash.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Trash compactor motor buzzing, often did not cycle

  • Customer: Jeffrey from San Mateo, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 37 of 40 people found this instruction helpful
First I removed the trash compactor from the cabinet and transported it to the garage to avoid scraping the kitchen floor....I then removed the the sheetmetal cover enclosing the motor by removing several sheetmetal screws. To remove the motor, I then removed the compactor drawer and tilted the compactor onto its front (the side you pull the drawer in and ... read more

New part problem, wire harness wrong

  • Customer: mark from colorado springs, CO
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 8 of 9 people found this instruction helpful
The wire harness from the part supplier was set up wrong, two of the three wires were switched and it damm near burned up the new motor. I had to correct the error by switching the wires around so that they matched the wireing from the original motor. read more

Foot release was not working properly making it difficult to open

  • Customer: Peter from Solon, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
I noticed that one of the holes that the foot pedal was attached to on the drawer assembly, had opened up so that the pivot pin wouldn't stay seated in it. I ordered a complete drawer assembly which included the metal trash container, drawer slides, and foot pedal assembly. The old front of the cabinet is removed by unscrewing about 8 screws. The front th... read more