This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if i...
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which a...
This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in y...
This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does no...
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts ou...
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door...
The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as the motor rotates. Ove...
The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following t...
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red fl...
This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing
$10.64
In Stock
Questions And Answers for GCET1031FS2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Eunice
December 11, 2019
No heat with dryer. Dryer does turn on and spin however. Dryer is part of a washer dryer stacker unit.
For model number GCET1031FS2
Hello Eunice, thank you for contacting us. You will want to replace the Thermal Limiter, part number PS419402 for your model dryer to fix this. Good luck with your repair!
Was this helpful?
Thank you for voting!
Sean
September 7, 2021
Dryer won't turn on anymore, i think i've narrowed it down to 2 possible culprits: The timer or the high limit thermostat. After my wife reported that it wasn't starting, i investigated to confirm, after it indeed didn't turn on right away, i started to move the timer to the other settings (as opposed to the minute timer) and it started working fine, i opened the door to shut it off. Started it again with no issues, moved the dial to the other alt setting and it started again, moved the dial to the regular timer setting and it indeed started running too, while it was running, i moved the timer dial while inside the minute timer zone slightly and it immediately shut off. I checked for heat and the dryer did produce heat.I kept moving the dials to see if i could start it again and as of right now haven't been able to start it again. i've tested the starter switch, thermal limiter, & the door switch for continuity; all seemed to be working as intended.
i hear no suspicious electrical/buzzing noise coming from the motor etc. in fact, i don't hear any subtle ticking coming from the timer either, i hear it from the washer's timer but not from the dryer's (when powered(does the dryer timer supposedly progress and make a tiny ticking noise when connected to the outlet? i'm not 100% certain whether it did...)) i haven't been able to access the high limiter thermostat as it's awkward to test but from my understanding that should only affect the heat situation, right? are there any other parts that i should be testing as-well, i don't have much knowledge of the timer's terminal wiring but was able to get good positive & negative continuity from the wall to the timer with toggling/turning the dial on & off.
thanks in advance
For model number GCET1031FS2
Hello Sean, thank you for your question. We have researched the model you have provided, and we would suggest the timer, part number PS418620. We hope this helps!
selected correct replacement knob. used small screw driver to remove small black metal sleeve from switch shaft. (had left that in place to be able to turn on dryer with needle nose pliers while waiting on knob). aligned flat of new knob with switch shaft and gently pressed into place.
Googled dryer start knob, Part Select was second site I clicked on, found within 1 min, part was inexpensive, easy to order, arrived quickly and fit perfectly. Excellent online ordering experience.
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum be
... Read morelt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
