Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GC932EXD6

GC932EXD6 Frigidaire Microwave Oven Combo - Overview

Get Parts and Repair Help for GC932EXD6

If you know the microwave oven combo repair part you need, you can browse the list of all parts on the GC932EXD6, or you can search by name or part description. You can also find your part by where it is located on the GC932EXD6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave oven combo. We’ve also included any installation videos we have for GC932EXD6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.93

Drip Pan

This drip pan is designed for gas cooktops and ranges. The pan has an approximate diameter of 8 inches, and the hole in the middle has a diameter of roughly 4 inches. The purpose o...

$6.68

Light Bulb

This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the internal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.

$50.79

Spark Module - 120V

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

$30.08

Clock Knob

This is a clock knob for an electric range, oven, or stove. It allows you to adjust the clock and cooking timer. No tools are required for this repair, the knob simply pops on and off the turn shaft. It is recommended to check all knobs on your appliance before ordering. This part is approximately 1/2 inch in diameter, is made of plastic, and is black in color. It is sold individually. This knob is a genuine original manufacturer part.

Door Hinge - Left Side

Door Hinge - Right Side

$60.52

Long Ceramic Igniter Assembly

$3.71

Thermostat Bulb Clip

$35.69

Gas Spark Ignition Switch

When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner

$165.19

Gas Oven Safety Valve

This safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range.

Common Symptoms of the GC932EXD6

[Viewing 1 of 1]
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.

  • Customer: Jonathan from Arkport, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 18 people found this instruction helpful
First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module not working if oven... read more

Two top burners would not light, defective switch

  • Customer: Donald from Middle Village, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 13 people found this instruction helpful
Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a minute. The switches ... read more

tHE ORIGINAL MODULE DIED AFTER 21 YEARS OF SERVICE

  • Customer: Jose from El Paso, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 11 of 16 people found this instruction helpful
First had to move the stove out of its "nest", take the side cover off, remove 1 screw and loosen the other , take the old module out and reverse the operation. That simple.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy. read more